If anyone's is interested, here are the plans for the tray
http://www.woodsmithshop.com/download/712/curved-handle-serving-tray.pdf
Ripping a 22.5° bevel.
Moderator: admin
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Well that simplifies things. The bevel cut is not "all the way across the edge".beeg wrote:If anyone's is interested, here are the plans for the tray
http://www.woodsmithshop.com/download/712/curved-handle-serving-tray.pdf
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
BuckeyeDennis
- Platinum Member
- Posts: 3814
- Joined: Tue Jul 24, 2012 10:03 pm
- Location: Central Ohio
I like those plans! If my wife ever finishes grading papers, I'm gonna ask her if she would like one of those. (I'm pretty sure that an Incra HingeMaster jig would be required in order to build it.beeg wrote:If anyone's is interested, here are the plans for the tray
http://www.woodsmithshop.com/download/712/curved-handle-serving-tray.pdf
)THANKS to everyone for the reply's. I think I'll start over and cut the bevel and groove on a wider piece, flat on the table.
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
.
.
Bob
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
How ya gonna tilt the table 67 1/2 degrees?]narrow[/B] edge gonna be 'flat' on the table?beeg wrote:THANKS to everyone for the reply's. I think I'll start over and cut the bevel and groove on a wider piece, flat on the table.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
dusty
- Platinum Member
- Posts: 21530
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
I have been thinking about this and have decided that this project is not as simple as it seems at first glance. If you need more input, let us know.beeg wrote:THANKS to everyone for the reply's. I think I'll start over and cut the bevel and groove on a wider piece, flat on the table.
Sketchup is getting to be a very useful tool. I have made this project about three times in Sketchup.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
Dusty, I'll take ANY input anyone wants to give.
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
.
.
Bob
-
dusty
- Platinum Member
- Posts: 21530
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
I have done this using Sketchup; there has been no saw dust. Therefore, there are no guarantees.
After playing with this in Sketchup, I have concluded that the two sides can be with the table tilted at any angle and that the three or four cuts can all be made without changing the table tilt.
I would start with the side pieces cut as 5/16" thick boards that measure 4"x16".
Then tilt the table right to 22.5° (or any other angle that seems appealing.). Do not change the table tilt until the next three or four cuts are completed.
[ATTACH]23809[/ATTACH]
Cut the dado.
[ATTACH]23810[/ATTACH]
Cut the bottom edge off.
[ATTACH]23811[/ATTACH]
Bottom edge gone. One cut left.
[ATTACH]23813[/ATTACH]
Final trim. Reorient work piece before making this cut.
After playing with this in Sketchup, I have concluded that the two sides can be with the table tilted at any angle and that the three or four cuts can all be made without changing the table tilt.
I would start with the side pieces cut as 5/16" thick boards that measure 4"x16".
Then tilt the table right to 22.5° (or any other angle that seems appealing.). Do not change the table tilt until the next three or four cuts are completed.
[ATTACH]23809[/ATTACH]
Cut the dado.
[ATTACH]23810[/ATTACH]
Cut the bottom edge off.
[ATTACH]23811[/ATTACH]
Bottom edge gone. One cut left.
[ATTACH]23813[/ATTACH]
Final trim. Reorient work piece before making this cut.
- Attachments
-
- beegs board cuts_step 1_cut dado (Custom).png (25.99 KiB) Viewed 3923 times
-
- beegs board cuts_step 2 cut bottom edge (Custom).png (20.51 KiB) Viewed 3923 times
-
- beegs board cuts_step 3 cut off bottom edge_bottom edge gone (Custom).png (24.41 KiB) Viewed 3923 times
-
- beegs board cuts_step 4 trim bottom edge (Custom) (2).png (28.3 KiB) Viewed 3920 times
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
One bevel cut is all you need.
I hope by now we realize that all we need is ONE SAW CUT to make two pieces that are 2 inches wide, with the bevel along one long edge. Just saw the bevel in the middle of a board that is wider than 4". Then saw the squared edge to get the 2" width.
If I were to make this, I would start with a board 3/4" thick and after sawing the bevel, plane to the 1/2" width.
If I were to make this, I would start with a board 3/4" thick and after sawing the bevel, plane to the 1/2" width.
Octogenarian's have an earned right to be a curmudgeon.
Chuck in Lancaster, CA
Chuck in Lancaster, CA
-
dusty
- Platinum Member
- Posts: 21530
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
I am embarrassed. No, I had not even thought of that. Yes, a very wise approach.charlese wrote:I hope by now that all we need is ONE SAW CUT to make two pieces that are 2 inches wide, with the bevel along one long edge. Just saw the bevel in the middle of a board that is wider than 4". Then saw the squared edge to get the 2" width.
If I were to make this, I would start with a board 3/4" thick and after sawing the bevel, plane to the 1/2" width.
That approach would, however, necessitate a change in the sequence of the cuts. Not a problem, just a different order.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.