Shop foundation

This is a forum for intermediate to advanced woodworkers. Show off your projects or share your ideas.

Moderator: admin

sharka
Silver Member
Posts: 10
Joined: Sun May 18, 2014 4:50 pm
Location: Beaumont, Texas

Shop foundation

Post by sharka »

Hi, have a question about putting in a new shed in the backyard.
Tired of working in the garage with no temp. control . The summer in S.E TX just kills the fun, getting old enough that I just don't want to deal with it anymore.think I will be having a new shed 16x24 built in the backyard on 8x16 blocks and skids. Backyard is clay , drainage is poor and sometimes stays saturated for several days after a heavy rain. blocks will be spaced every 4' down and across. Is there anything else that needs to be done or do you think I will have a leveling problem? anyone have or had to deal with this concern? Thanks.
User avatar
"Wild Bad Bob"
Platinum Member
Posts: 1065
Joined: Fri Mar 28, 2014 2:03 pm
Location: Germantown, Wi

Post by "Wild Bad Bob" »

I am not familiar with TX soil and weather, I was a general, "hands on" contractor, and built many additions to homes, but instead of the blocks, what about the concrete form tubes, set holes at proper distances, dig holes for the tubes, allowing for some height above the grade, level of course, fill with concrete, and put your perimeter joist on them.
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
User avatar
rjent
Platinum Member
Posts: 2121
Joined: Fri Mar 14, 2014 3:00 pm
Location: Hot Springs, New Mexico

Post by rjent »

rbursek wrote:I am not familiar with TX soil and weather, I was a general, "hands on" contractor, and built many additions to homes, but instead of the blocks, what about the concrete form tubes, set holes at proper distances, dig holes for the tubes, allowing for some height above the grade, level of course, fill with concrete, and put your perimeter joist on them.
This X10. :)

put large gravel at the bottom of the tube holes to help with drainage. Depending on how deep the clay is, you might think about drilling auger holes deeper than the clay (and away from the structure) and back filling with gravel. You might be able to effectively drain the area. We have gotten rid of alkali fields that way here in NM.

JMHO
Dick
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....

"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
Gene Howe
Platinum Member
Posts: 3219
Joined: Wed Jul 26, 2006 7:52 pm
Location: Snowflake, AZ

Post by Gene Howe »

I add ++ on using the Sonotubes. We used 2' ones for our raised deck. Easypeasy.
We over built. Poured them @ 4' OC. But the deck NEVER moves!
Gene

'The true soldier fights not because he hates what is in front of him, but because he loves what is behind him.' G. K. Chesterton
sharka
Silver Member
Posts: 10
Joined: Sun May 18, 2014 4:50 pm
Location: Beaumont, Texas

Post by sharka »

Thanks for the replies, was hoping that the blocks would be sufficient, digging and filling 24 piers becomes a project itself. When I lived in the country I owned a tractor with attachments including an auger, I sure miss living in the country.
User avatar
fredsheldon
Platinum Member
Posts: 1175
Joined: Tue Jan 17, 2012 1:31 pm
Location: The Woodlands, Texas

Post by fredsheldon »

sharka wrote:Hi, have a question about putting in a new shed in the backyard.
Tired of working in the garage with no temp. control . The summer in S.E TX just kills the fun, getting old enough that I just don't want to deal with it anymore.think I will be having a new shed 16x24 built in the backyard on 8x16 blocks and skids. Backyard is clay , drainage is poor and sometimes stays saturated for several days after a heavy rain. blocks will be spaced every 4' down and across. Is there anything else that needs to be done or do you think I will have a leveling problem? anyone have or had to deal with this concern? Thanks.
I blew in 6 inches of insulation above my two car attached garage using a free blower from Lowes, installed insulation panels on the inside of my double garage door and installed a 15,000 BTU ductless A/C and my garage/shop is a cool 72 degrees on a 100 degree outside day. My electric bill went up on average $20 per month and I worked in the shop every evening and all day weekends for a year. It also is very easy to warm with a small space heater in the winter. And I live in the Houston area.
Fred Sheldon
The Woodlands, Tx
'52 10ER # 60869 (restored in 2012, used as a dedicated drill press), '52 10ER # 88712 (restored 01/2013), 52 10ER # 71368 (in process of restoring), '83 500 Shorty with OPR installed, '83 520 PowerPro with Lift Assist, 6" Joiner, 6" Belt Sander, 18" Jig Saw, 11" Band Saw, 12" ProPlaner, SS Crosscut Table. SS Dust Collector, Hitachi 1/2" router, Work Sharp 3000 with all attachement, Nova G3 Chuck, Universal Tool Rest, Appalachia Tool Works Sled.
User avatar
Ed in Tampa
Platinum Member
Posts: 5834
Joined: Fri Jul 21, 2006 12:45 am
Location: North Tampa Bay area Florida

Post by Ed in Tampa »

fredsheldon wrote:I blew in 6 inches of insulation above my two car attached garage using a free blower from Lowes, installed insulation panels on the inside of my double garage door and installed a 15,000 BTU ductless A/C and my garage/shop is a cool 72 degrees on a 100 degree outside day. My electric bill went up on average $20 per month and I worked in the shop every evening and all day weekends for a year. It also is very easy to warm with a small space heater in the winter. And I live in the Houston area.

Your AC is it a window unit or something else?
Ed in Tampa
Stay out of trouble!
sharka
Silver Member
Posts: 10
Joined: Sun May 18, 2014 4:50 pm
Location: Beaumont, Texas

Post by sharka »

Thanks for the input Fred, I have considered doing something similar but really prefer to give the garage back to the wife, I like for her to park in the garage although I use the driveway myself. However, yard tools will remain in the garage and the fun tools will go to the shed.
User avatar
Jack Wilson
Gold Member
Posts: 186
Joined: Tue Jul 09, 2013 10:40 pm
Location: Ponte Vedra, FL

Post by Jack Wilson »

You can rent an auger for about $150.00 a day. One that is on wheels that you can roll right up to where you want to dig a hole. I am sure you could get them all dug on less than a day.
SS Mark 7 PowerPro, 2 SS Bandsaws, SS Belt Sander, SS Jigsaw, 13" Steel City Lunch Box Planer, SS Jointer, Jet 22-44 Drum Sander
garys
Platinum Member
Posts: 2075
Joined: Wed Mar 02, 2011 12:16 am
Location: Bismarck, ND

Post by garys »

Check your local building codes. That wouldn't meet code here and you would get to do it over. A foundation like that becomes a rodent hotel.
Post Reply