Shop foundation
Moderator: admin
Shop foundation
Hi, have a question about putting in a new shed in the backyard.
Tired of working in the garage with no temp. control . The summer in S.E TX just kills the fun, getting old enough that I just don't want to deal with it anymore.think I will be having a new shed 16x24 built in the backyard on 8x16 blocks and skids. Backyard is clay , drainage is poor and sometimes stays saturated for several days after a heavy rain. blocks will be spaced every 4' down and across. Is there anything else that needs to be done or do you think I will have a leveling problem? anyone have or had to deal with this concern? Thanks.
Tired of working in the garage with no temp. control . The summer in S.E TX just kills the fun, getting old enough that I just don't want to deal with it anymore.think I will be having a new shed 16x24 built in the backyard on 8x16 blocks and skids. Backyard is clay , drainage is poor and sometimes stays saturated for several days after a heavy rain. blocks will be spaced every 4' down and across. Is there anything else that needs to be done or do you think I will have a leveling problem? anyone have or had to deal with this concern? Thanks.
- "Wild Bad Bob"
- Platinum Member
- Posts: 1065
- Joined: Fri Mar 28, 2014 2:03 pm
- Location: Germantown, Wi
I am not familiar with TX soil and weather, I was a general, "hands on" contractor, and built many additions to homes, but instead of the blocks, what about the concrete form tubes, set holes at proper distances, dig holes for the tubes, allowing for some height above the grade, level of course, fill with concrete, and put your perimeter joist on them.
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
- rjent
- Platinum Member
- Posts: 2121
- Joined: Fri Mar 14, 2014 3:00 pm
- Location: Hot Springs, New Mexico
This X10.rbursek wrote:I am not familiar with TX soil and weather, I was a general, "hands on" contractor, and built many additions to homes, but instead of the blocks, what about the concrete form tubes, set holes at proper distances, dig holes for the tubes, allowing for some height above the grade, level of course, fill with concrete, and put your perimeter joist on them.
put large gravel at the bottom of the tube holes to help with drainage. Depending on how deep the clay is, you might think about drilling auger holes deeper than the clay (and away from the structure) and back filling with gravel. You might be able to effectively drain the area. We have gotten rid of alkali fields that way here in NM.
JMHO
Dick
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....
"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....
"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
- fredsheldon
- Platinum Member
- Posts: 1175
- Joined: Tue Jan 17, 2012 1:31 pm
- Location: The Woodlands, Texas
I blew in 6 inches of insulation above my two car attached garage using a free blower from Lowes, installed insulation panels on the inside of my double garage door and installed a 15,000 BTU ductless A/C and my garage/shop is a cool 72 degrees on a 100 degree outside day. My electric bill went up on average $20 per month and I worked in the shop every evening and all day weekends for a year. It also is very easy to warm with a small space heater in the winter. And I live in the Houston area.sharka wrote:Hi, have a question about putting in a new shed in the backyard.
Tired of working in the garage with no temp. control . The summer in S.E TX just kills the fun, getting old enough that I just don't want to deal with it anymore.think I will be having a new shed 16x24 built in the backyard on 8x16 blocks and skids. Backyard is clay , drainage is poor and sometimes stays saturated for several days after a heavy rain. blocks will be spaced every 4' down and across. Is there anything else that needs to be done or do you think I will have a leveling problem? anyone have or had to deal with this concern? Thanks.
Fred Sheldon
The Woodlands, Tx
'52 10ER # 60869 (restored in 2012, used as a dedicated drill press), '52 10ER # 88712 (restored 01/2013), 52 10ER # 71368 (in process of restoring), '83 500 Shorty with OPR installed, '83 520 PowerPro with Lift Assist, 6" Joiner, 6" Belt Sander, 18" Jig Saw, 11" Band Saw, 12" ProPlaner, SS Crosscut Table. SS Dust Collector, Hitachi 1/2" router, Work Sharp 3000 with all attachement, Nova G3 Chuck, Universal Tool Rest, Appalachia Tool Works Sled.
The Woodlands, Tx
'52 10ER # 60869 (restored in 2012, used as a dedicated drill press), '52 10ER # 88712 (restored 01/2013), 52 10ER # 71368 (in process of restoring), '83 500 Shorty with OPR installed, '83 520 PowerPro with Lift Assist, 6" Joiner, 6" Belt Sander, 18" Jig Saw, 11" Band Saw, 12" ProPlaner, SS Crosscut Table. SS Dust Collector, Hitachi 1/2" router, Work Sharp 3000 with all attachement, Nova G3 Chuck, Universal Tool Rest, Appalachia Tool Works Sled.
- Ed in Tampa
- Platinum Member
- Posts: 5834
- Joined: Fri Jul 21, 2006 12:45 am
- Location: North Tampa Bay area Florida
fredsheldon wrote:I blew in 6 inches of insulation above my two car attached garage using a free blower from Lowes, installed insulation panels on the inside of my double garage door and installed a 15,000 BTU ductless A/C and my garage/shop is a cool 72 degrees on a 100 degree outside day. My electric bill went up on average $20 per month and I worked in the shop every evening and all day weekends for a year. It also is very easy to warm with a small space heater in the winter. And I live in the Houston area.
Your AC is it a window unit or something else?
Ed in Tampa
Stay out of trouble!
Stay out of trouble!
- Jack Wilson
- Gold Member
- Posts: 186
- Joined: Tue Jul 09, 2013 10:40 pm
- Location: Ponte Vedra, FL
You can rent an auger for about $150.00 a day. One that is on wheels that you can roll right up to where you want to dig a hole. I am sure you could get them all dug on less than a day.
SS Mark 7 PowerPro, 2 SS Bandsaws, SS Belt Sander, SS Jigsaw, 13" Steel City Lunch Box Planer, SS Jointer, Jet 22-44 Drum Sander