New Owner

wodnek · Post by **wodnek** » Wed Sep 24, 2014 9:30 am

Hi, I am new to the forums, as I just bought my Shopsmith mark V yesterday. I was looking for a shaper on craigslist, and I came up with a shopsmith as one of the hits. Up until Sunday, I hadn't known of their existence. Here are soe pictures of what i got. I have a few pieces of "furniture" to make and then hope to make cabinets for the kitchen. I have done a bit of woodworking over the years, but this will be an ambitious task. Ultimately, without going with a custom cabinet shop, i can't just order what i want. (well maybe I mean what my Wife wants)

beeg · Post by **beeg** » Wed Sep 24, 2014 10:42 am

Welcome to the forum Wodnek.
Looks like you'll need just a little cleanup, waxing, lubing and alignment. You'll be ready to go.

joedw00 · Post by **joedw00** » Wed Sep 24, 2014 11:11 am

Welcome to the forum, looks like they took good care of it,

JPG · Post by **JPG** » Wed Sep 24, 2014 1:29 pm

Welcome indeed!

I refer you to the two sticky posts at the top of the Maintenance and Repair forum.

Looks in good condition, but a little pm now will pay off later.

wodnek · Post by **wodnek** » Wed Sep 24, 2014 1:46 pm

Thankfully the second owner took good care of it. He walked me through how he waxed it, how to disassemble the headstock, etc. He also gave me touch up paint. He clearly took good care of it. Ultimately, a shaper is why i looked at this, but I always tried to justify acquiring a lathe. I am sure I will use most of the functions, with the exception of the table saw. I have two craftsman table saws, one from the 40s, and one from the 80s. I will keep an eye out on craigslist for another package, I wouldn't mind the bandsaw, duplicator, and biscuit joiner. no hurry t pay ebay prices.

charlese · Post by **charlese** » Wed Sep 24, 2014 2:03 pm

Thought I'd just throw in a link to the Shopsmith page that has the list of all the shaper cutters they have. Not intending to sell you something, only to allow you to see their selection.
Scroll down to the list showing shaper cutters and molding knives.
http://www.shopsmith.com/ownersite/cata ... utters.htm

wodnek · Post by **wodnek** » Wed Sep 24, 2014 3:12 pm

I was there yesterday. Does anyone know if the cabinet set has everything you need to make the doors? Both the raised panel, and the frame?

joedw00 · Post by **joedw00** » Wed Sep 24, 2014 3:48 pm

I would say it had all listed.

Door Panel
Door-Rail Coper
1/4-inch Groove
1/2-inch Radius
1/2-inch Grove
3-Bead edge
Complete Cabinet Set

505937
Complete Cabinet Set -- Six Cutters Total
Price $104.15
Status: Quantity is low.

JPG · Post by **JPG** » Wed Sep 24, 2014 5:08 pm

wodnek wrote:Thankfully the second owner took good care of it. He walked me through how he waxed it, how to disassemble the headstock, etc. He also gave me touch up paint. He clearly took good care of it. Ultimately, a shaper is why i looked at this, but I always tried to justify acquiring a lathe. I am sure I will use most of the functions, with the exception of the table saw. I have two craftsman table saws, one from the 40s, and one from the 80s. I will keep an eye out on craigslist for another package, I wouldn't mind the bandsaw, duplicator, and biscuit joiner. no hurry t pay ebay prices.

Like yer truck license plate!

Still looking for "4"?

JPG · Post by **JPG** » Wed Sep 24, 2014 5:26 pm

wodnek wrote:Thankfully the second owner took good care of it. He walked me through how he waxed it, how to disassemble the headstock, etc. He also gave me touch up paint. He clearly took good care of it. Ultimately, a shaper is why i looked at this, but I always tried to justify acquiring a lathe. I am sure I will use most of the functions, with the exception of the table saw. I have two craftsman table saws, one from the 40s, and one from the 80s. I will keep an eye out on craigslist for another package, I wouldn't mind the bandsaw, duplicator, and biscuit joiner. no hurry t pay ebay prices.

Like yer truck license plate!

Still looking for "4"?