ERLover wrote:You did well!!!! The vac took it over the top, jointers are a dime a dozen around here. Johnsons paste wax. I will let others tell you oil, but I use 20w machine oil. Cant remember the name, big box stores carry it and I get the one with the 6"tube extender.
Sounds like you got a steal! Watch the sawdust session maintenance videos, you will be glad you did. A Zoom Spout Oiler will let you put the oil where you want it without making a mess.
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!
should be on the left, and about only a 1/16" out of alignment with coupling at most.
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
Some plastic cylinder with a spring on one end. Says accessory and headstock with arrows
That would be the drive coupler for your spt's (jointer, bandsaw, etc).
Thanks Bruce! Just watched a YouTube video and the guy had it coupled to a band saw. The jointer is still like an inch above the headstock. Does it matter if jointer is on left or right?
Jointer only works on left and is driven by the lower(idler) shaft.
Inch above the headstock? Think we need to see a pix.
#10 machine oil - sewing machine oil - 3 in one oil - turbine oil - electric motor oil - fan oil - zoom spout recommended. WD 40 - NO!
Universal motor?
5 0 5 gauge?
2 rip fences and 2 miter gauges each different?
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Figured it out. The left handle was loose. Tightened it up which pulled the square nuts inside. Jointer is good.
Universal motor? My iPad must have corrected from universal arbor.
5-0-5 gauge is the small fine adjustment for the table. It goes 90-0-45 then right next to it is a small silver scale of 5-0-5. I have an extra of those.
Miter gauges are same. Just one has the grip attached.
One large fence and a smaller fence. Not sure where or what the smaller one does.
Just started watching sawdust lecture of maintenance.
B4 JPG does his famous line, "'post pics"' I will, post pics
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
Here is the SS I just purchased. No I'm not selling it, easiest way to show pics.
1- vacuum
2- SS
3- jointer
4- saw blades and accessories
5- accessories
6- random attachments I don't know what they are
7- random piece
8- fence and smaller fence
9/10 inside
Blew out saw dust and cleaned outside so far after pics were taken. Oiling and waxing tomorrow. I want to take jointer apart er and go through it thoroughly.
It was JPg spoof, not on you, nice buy. Lighten up
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
Posting pix here is easier than a spoof craigslisting.
Clipboard0x.jpg (91.11 KiB) Viewed 9317 times
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
