- IMG_52DAF07CA3AC-1.jpeg (1.61 MiB) Viewed 19155 times
Wannigan/Cooler Build
Moderator: admin
Re: Wannigan/Cooler Build
7 AM 8/15 (total elapsed time 64 hours 15 minutes). Still going strong. Internal thermometer 32 (as explained by Dusty and JPG it should stay there until the ice is gone). Overnight low temperature was 68 degrees.
Last edited by algale on Wed Aug 15, 2018 6:53 pm, edited 2 times in total.
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!
-
dusty
- Platinum Member
- Posts: 21530
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Wannigan/Cooler Build
I have never timed the departure of ice from either of my two coolers but I do believe I would have had nothing but water long ago.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
Re: Wannigan/Cooler Build
Are you draining the water off or leaving it?
I was thinking a calculation on ice melt might be interesting. Weigh the ice that goes in and the water that comes off like every 6 hours would show a good indication of ice loss over time.
Sounds like a science project to me.
Ed
I was thinking a calculation on ice melt might be interesting. Weigh the ice that goes in and the water that comes off like every 6 hours would show a good indication of ice loss over time.
Sounds like a science project to me.
Ed
{Knight of the Shopsmith} [Hero's don't wear capes, they wear dog tags]
Re: Wannigan/Cooler Build
Leaving it. For what it's worth, the Yeti website has a page on ice management that recommends against draining off the melted water.reible wrote:Are you draining the water off or leaving it?
I was thinking a calculation on ice melt might be interesting. Weigh the ice that goes in and the water that comes off like every 6 hours would show a good indication of ice loss over time.
Sounds like a science project to me.
Ed
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!
Re: Wannigan/Cooler Build
6:45 PM 8/15. Total elapsed time: 76 hours. Still 32 on the inside thermometer. Today's high temperature was 89 degrees.
The melt rate appears to be picking up pace but the beer is sill perfectly chilled!
The melt rate appears to be picking up pace but the beer is sill perfectly chilled!
- IMG_3CD2C4A4BEAF-1.jpeg (1.42 MiB) Viewed 19107 times
Last edited by algale on Wed Aug 15, 2018 6:52 pm, edited 2 times in total.
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!
Re: Wannigan/Cooler Build
You are approaching 3 days. Very impressive!!!algale wrote:6:45 PM 8/15. Total elapsed time: 64 hours. Still 32 on the inside thermometer. Today's high temperature was 89 degrees.
The melt rate appears to be picking up pace but the beer is sill perfectly chilled!
IMG_3CD2C4A4BEAF-1.jpeg
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
Re: Wannigan/Cooler Build
Error in my calculation. It's 76 hours -- more than three days. Correction made in post above.
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!
-
BuckeyeDennis
- Platinum Member
- Posts: 3814
- Joined: Tue Jul 24, 2012 10:03 pm
- Location: Central Ohio
Re: Wannigan/Cooler Build
The beers seem to be dwindling! Will they even outlast the ice? 
Re: Wannigan/Cooler Build
Those beers are evaporating.BuckeyeDennis wrote:The beers seem to be dwindling! Will they even outlast the ice?
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Wannigan/Cooler Build
The water is likely near 32 and does not change when it is opened(hence the do not drain advice).
It should stay near 32 until almost the last chunk of ice is melted.
That last chuck will melt quite quickly I predict. The available 'heat of fusion' will diminish quickly with the decreasing mass.
It should stay near 32 until almost the last chunk of ice is melted.
That last chuck will melt quite quickly I predict. The available 'heat of fusion' will diminish quickly with the decreasing mass.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange