Schedule a Meeting · Talk to a real woodworker: +1 937-890-5197 · 8:00AM – 4:30PM ET

Need help for my small shop

seajay62

I really need some help to solve my dilemma. I have a small shop (1 bay of a 2 bay garage)and too much stuff in it. I have gotten to the point of not being able to effectively work in the shop and that's not fun.

I have a workbench, a shopsmith M V 520, a shopsmith M V 500 shorty that I use for sanding and lathe work, a craftsman RAS and a dewalt planer each on a roll around cabinet, a shopsmith stand-alone scroll saw, a shopsmith old style overhead router table plus a portable router table top with the Incra Universal positioning jig (the original plastic version) which I use clamped in the workbench vice. I also have a shopsmith joiner and bandsaw. In addition, I have some storage cabinets, my shop vac with the Oneida dust-deputy attached, and a roll-around clamp cart. I can barely move around and must reposition things to work with any tool. I need help to reduce the clutter and please don't suggest that you would be happy to give my tools a new roomier home.

I am thinking about selling the overhead router set-up and possibly the scroll saw since I rarely use it.

Then, I am considering purchasing the shopsmith Pro Fence Router Table System. This would give me a router table set-up without using too much floor space and it can be stored when not in use.

Also, if I purchase the power-pro headstock and the Mk7 conversion, I can then rout both from above and below. This set-up seems to allow me to effectively get the benefits of the overarm pin router attachment in addition to everything else from the power-pro headstock. Unfortunately, the overarm set-up doesn't have enough table room to use the Incra positioning jig so I need the other router table set-up.

The order that I would do things would be as follows:

sell the overhead router table set-up and possibly the scroll saw

Purchase the pro fence router table

Purchase the power-pro headstock

purchase the M 7 conversion

Timing of purchases would be based on finances.

Am I making sense? Am I missing something? Do you have any alternative solutions? Any input would be greatly appreciated.

rjent

I am far from having usable knowledge, but it seems to me you have a lot of "stand alone" shopsmith devices. Maybe get some of them off of the "shorties", stands, etc and put them on racks?

As far as the Mark 7 upgrade, don't hesitate. :)

JMHO :)

algale

There's no reason you could not do as you say. Whether it is the best plan of action for you given your space limitations is a question that only you can answer.

charlese

algale wroteThere's no reason you could not do as you say. Whether it is the best plan of action for you given your space limitations is a question that only you can answer.

Ditto to what algale said! One thing I have found really helpful in my crowded shop is Shopsmith's clear dust collector hose. It is extremely flexible, can be looped over anything and is really tough. It can be stepped on with no harmful effects. No more fighting with hoses!

http://www.shopsmith.com/ownersite/catalog/dc_hoses.htm

inpursuit

Last Christmas I had a 30x80 barn and shop. The weekend before Christmas a small tornado came through and wiped out the barn leaving a 30x30 shop area which I am building back. My wife just ordered me a ss 7. Can't wait to get it here. Got electrician coming out tomorrow to give me estimate on all my electrical needs. BTW hi guys I'm in central Texas. I will probably be on here a lot looking for advise and help

Bill

Ed in Tampa

Since you are going with a Mark 7 conversion why not get the Shopsmith deputy conversion and dump the shorty that will free up some floor space? You can put the deputy on a roll around cart and have tons of storage underneath.

Mike907

If you are getting a PowerPro 7, be sure to put in 220V outlets wherever you might like to use the Shopsmith, so that you can get the full horsepower rating.

Mike

BuckeyeDennis

Some guys use half of their garage to store their tools, and then "borrow" the other half and wheel the tools over when actually working. Would that make any sense for you?

How often do you use the RAS? If the answer is "occasionally", you might consider integrating it into a workbench, and just keep the the arm swung back when not in use.

I've been working on my own workshop layout lately, and found that adding a RAS actually freed up tons of space. By using a RAS for your crosscutting and cross-dadoing, you don't have to maintain a huge amount of side clearance for your SS (or tablesaw), nor do you have to feed a long unwieldy board sideways for crosscutting.

aloibl

INPURSUIT - where in Central Texas are you located at?

seajay62

Apparently many people looked at this post but only a few had any ideas to offer. I read through those responses and will specifically use the long hose idea and will add 220v outlets when I upgrade to the power pro. Meanwhile, I think I'm going to take a very conservative approach due to financial and space considerations.

I will sell the overhead router set-up. That eliminates one item taking up valuable floor space. Instead of getting the pro fence router table, I will make my own router table similar to the one in the following thread:

https://forum.shopsmith.com/viewtopic.php?t=9735

( I don't know how to provide a live link but if you click on the link while pressing CTRL key will take you there.) After the initial post, see page 3, post #29 for a 520 fit. I only have to purchase front and rear rails and a router plate. This seems to be the quickest and cheapest way to move forward at this time.

The upgrades to the power pro and M7 conversion will have to wait.

Writing this thread caused me to think through my options and your input plus browsing through old threads has been helpful. It's like having a buddy here to discuss my options. Thanks for the ability to utilize this forum.

charlese

seajay62 wrote...Writing this thread caused me to think through my options and your input plus browsing through old threads has been helpful. It's like having a buddy here to discuss my options. Thanks for the ability to utilize this forum.

I believe your many buddies also appreciate having you here. I know I do!:)

henecle

It's very doable with in one half of a two-car garage. I solved the problem by remodeling the garage and adding a floor to ceiling wall down the center and using a pocket door between the two sides. All walls covered with OSB, new breaker box with additional 110 and new 220 circuits, overhead fluorescent lighting, PSI Air Filtration and overhead radiant heater. It took some designing but the final results were well worth the effort.