Buying a Used Shopsmith Mark V

A checklist to help you find the bargains and avoid the basketcases 

When search for tools, whether used or new, it’s useful to keep your true goal in focus. 
No one buys tools because they want tools - they want what tools can do. You are 
considering buying a used Mark V because you want to remodel your home, build some 
new kitchen cabinets, make toys for the grandkids, or pursue some private vision of 
yourself as a skilled craftsman or creative artisan. Tools, especially good tools, will help 
you achieve these worthy ambitions and they are an essential ingredient for your 
eventual success, but they are not the only ingredient or even the most important. What 
you need first and foremost is the knowledge to use these tools effectively. 

This is not just important, it’s pivotal - and that’s why I’ve put it first on this checklist. 
You are considering buying a Mark V because: 

• 
You’ve heard it’s a quality tool. 
• 
It packs a lot of capability into a small space. 
• 
Its unique design allows it to do many things other stand-alone tools can’t. 
• 
It’s a great tool to learn on if you want to explore woodworking as a potential 
vocation or avocation. 
• 
It’s a decades-old tried-and-true woodworking system. 
• 
The older machines are well-supported, serviceable, and upgradable. 
All of this is true, but I suggest you add one more item - education. Try to find a tool 
manufacturer that has authored more information about using its tools, or more know-
how about the craft of woodworking. There are none that even come close to Shopsmith. 

A little history

The Shopsmith 5-in-1 system was the brainchild of inventor Hans Goldschmidt who 
organized a company called Magna Engineering just after World War II. They released 
their first tool in 1947, the Shopsmith 10ER (Model 10, Experimental, Revised, in case 
you’re wondering). It was well received, and Magna made dozens of improvements of 
the next 7 years, and in 1954 released the Shopsmith Mark V. Although there were 
other “Marks” - a Mark II and a Mark VII - the Mark V was the flagship. The design has 
been manufactured steadily by several companies since Magna, with well over a million 
sold. 

Although newer Shopsmiths look much the same as older ones, the design has not 
remained unchanged. There have been dozens of improvements made over the years, 
and you need to be aware of at least the most important of these as you shop for a used 
machine. Yes, you can update a 1954 Mark V to have all the same improvements and 
capabilities as one made this year. Yes, there are service parts and service people who 
can help you make the most hopeless basketcase useful and productive once again, 
but it will cost you. And it may cost you many times the purchase price to restored an 
older machine that has not been well-cared for. So it’s worth you while to take a good 
look under the hood and consider all the hidden expenses before you buy a used 
machine. 

Page 1 of 5 


Breaking it down

Because it’s designed to do more than one operation, the Mark V is more complex than 
most consumer power tools. It helps to break the machine down into its component 
systems and consider each sub-system on its own, part by part. There are four of these 
sub-systems: 

• 
Headstock, consisting of the motor, speed changer, arbors, and movable quill. 
• 
Main Table, consisting of the table, trunnions, carriage, and table-raising 
mechanism. 
• 
Frame, consisting of legs, tubes, headrest, and pivoting base. 
• 
Accessories, consisting of parts for each of the five functions - sawing, drilling, 
boring, turning, and sanding - as well as some accessories for extra support, 
safety, maintenance, and setup. 
Headstock 
The headstock contains an electrical motor with a non-standard mount and shaft - you 
cannot go out a buy one of these off the shelf, so you want to be sure the one you get is 
in good shape. On the shaft of that motor are two floating sheaves (half-pulleys) and a 
V-belt that turns an idler shaft with two more floating sheaves. The idler shaft turns the 
drive shaft at the top of the headstock via a flat belt. As you turn the speed changer, 
the sheaves on one shaft get closer together and the sheaves on the other get further 
apart. This changes the speeds at which all three of the power take-offs or arbors turn 
- one at the end of the quill at the front of the headstock and two at the back. The quill 
extends and retracts from the headstock, like the quill of a drill press. Additionally, there 
is a switch to turn the motor off and on, and a headstock lock to secure it in position 
on the tubular frame. 

• 
The Number One Thing to remember when looking over a used Shopsmith is 
don’t turn the speed changer unless the motor is running. If the seller 
adheres to the standard “you break it; you bought it” policy, you might find 
yourself the proud owner of the used Shopsmith in need of expensive repairs. 
• 
Mark Vs made before 1962 (Serial No. 37143) have 3/4 horsepower motors; 
those made afterwards have 1-1/8 horsepower. The extra oomph makes a big 
difference. Older machines bog down easier. You can install the more powerful 
motor, but they are costly. 
• 
Prior to 1962 (Serial No. 37143), early headstocks used a toothed “Gilmer” drive 
belt between the idler and drive shafts. These are less durable the newer “Poly-
V” belts. They are also less forgiving. The poly-V belts will slip if there is some 
event that brings the drive train to a sudden halt; the Gilmer belts will not and 
internal parts may be damaged as a result. 
• 
Early headstocks made in 1954 and 1955 had no access hole (covered by a 
Shopsmith logo) on the side of the headstock; making it extremely difficult to 
lubricate the interior parts of the speed changer and clean the teeth of the quill. 
You can have these holes machined, but that’s another expense you may not 
want to shell out. 
• 
Headstock made after 1984 (Serial No.190000) have a two-bearing quill. These 
run smoother and have one-fifth the “run-out” as the older single-bearing quills, 
making it much easier to be accurate when drilling. 
• 
With 1988, Shopmith began using the date of manufacture as the serial number 
- mm/dd/yyyy. Knowing that makes it easier to know the true age of a machine, 
Page 2 of 5 


• 
In 1991 (Serial No. 01011991), Shopsmith introduced a new headstock with a 
red safety switch, replacing the older toggle switch. 
• 
Check that the speed changer and the sheaves move easily and are not frozen. 
Machines that have been mishandled by people who don’t know enough not to 
turn the speed changer if the motor isn’t running may have problems you don’t 
want to seal with. Those that have not been properly lubricated or have been 
stored for a long time may have a jammed drive train. Remove the cover at the 
back of the machine, turn on the motor, and run the speed changer up and down 
several times while watching the movement of the sheaves. 
• 
Check that the quill extends easily and then retracts with its own spring tension. 
• 
Check that the headstock locks are not worn. Tighten them ¼ turn past snug, 
then loosen them and try to move the headstock. If you hear the locks “pop” 
when you loosen them, they are probably worn and need replaced. It the 
headstock won’t move until you struggle with it, the locks and possibly the tubes 
need some careful maintenance. 
Main Table 
The table has two miter gauge slots, one on each side of the table insert, where the 
saw blade and other cutters pokes up above the table. The table tilts through 135 
degrees (90 degrees left, 45 degrees right), pivoting on a table tie bar supported by two 
table posts. One or two trunnions and the table tilt lock secure the table at the 
desired angle. Racks of teeth in the table support posts and two pinions raise and 
lower the table in the carriage. The carriage lock secures the carriage in position on 
the frame. 

• 
Prior to 1985 (Serial No. 196119), the Shopsmith Mark V had but one model. In 
1985, Shopsmith introduced the Model 510 with a much larger table (171/2” x 
22”) and two trunnions (one in the front, one at the back). Not only did this 
provide more support surface, the two-trunnion system was much more stable 
when the table was locked at a specific angle. The older configuration with the 
single trunnion and a smaller table was designated the Model 500. 
• 
With the introduction of the Model 510 in 1985, Shopsmith began to cut T-slots 
in the tables rather than standard miter gauge grooves. The also added T-slots to 
the surfaces of the fence. This helped with the handling of large workpieces and 
made it possible to mount various jigs and fixtures to the table or fence. 
• 
The Model 510 also used a different shape for the table inserts. The design 
made it easier to mount and dismount the upper saw guard. 
• 
In 1999 (Serial No. 01011999), Shopsmith introduced the Model 520 with a larger 
and more stable “Pro-Fence” system - and more T-slots in the fence for 
increased capabilities. 
• 
Both the Model 510 and 520 offered the possibility of add floating extension 
tables between the main table and the auxiliary table (a standard accessory). 
• 
Checks that the table tilts easily and locks securely in place and any angle. If the 
table binds badly when you are tilting it, the tie bar may be bent. 
• 
Check that the table can be raised and lowed easily and locks at the desired 
height. Difficulty changing the table height may also indicate a bent tiebar, as well 
as worn pinions or a buggered rack. 
Page 3 of 5 


• 
Check that the carriage slides easily on the way tubes. As check that the locks 
are not worn - this is done in the same manner as testing the headstock locks 
(see above). 
Frame 
The Mark V is supported on two metal legs. The left leg (as you face the speed changer 
dial and power switch) supports the headrest; right leg supports the base. The base 
and the headrest are joined by two bench tubes. Two way tubes run between the 
pivoting section of the base and a way tube tie bar. The tie bar rests in the headrest 
and is secured by the headrest lock when all four tubes are horizontal. When the way 
tubes pivot to a vertical position, the arm lock secures them. There have been very few 
improvements to the basic frame over the year; the old design is pretty hard to beat. 
However, there are a few things: 

• 
Prior to 1973 (Serial No. 1001), the way tubes and bench tubes has extremely 
thick walls. Only the way tubes were plated; the bench tubes were painted. 
Beginning in 1973, all four tubes were plated and had thinner walls. 
• 
The frame has been painted several different colors over the years. 
o 
1953 to 1960 machines were painted a two-tone green. These are 
affectionately known as “greenies.” 
o 
1960 to 1963 saw a two-tone brown and are known as “goldies.” 
o 
1963 to 1967 machines were painted a smooth gray. Same with 1973 to 
1984 machines. 
o 
From 1984 on, the Mark Vs have been painted a rough gray. 
• 
Check the surface condition of the way tubes. If the headstock or the carriage 
locks have ever been overtightened, the surfaces will be dented. Small dents 
probably won’t affect the motion of the headstock and carriage; large ones will. 
• 
Also look for corrosion on the way tubes, especially rust pits. Pitted surfaces 
may also interfere with the movement of the headstock and carriage. 
• 
Check the bolts the hold the legs to the headrest and base. These occasionally 
vibrate loose. On older machines, you are likely to find bolts missing or an odd 
assortment of bolts. 
• 
Check that the arm lock is in place. This is sometimes removed and goes AWOL. 
Accessories 

Here, the most important question is, “Does the machine come with all the accessories 
it once had?” followed by, “Which ones are missing?” 

• 
Sawing Accessories - Mark V generally came with a combination saw blade, 
saw arbor, arbor wrench, lower saw guard, upper saw guard, miter gauge, and 
miter gauge hold-down. 
• 
Sanding Accessories - There should be at least one metal sanding disc. Prior 
to 1967, these were made of cast aluminum; after 1973, steel. It’s probably too 
much to hope for that these will be many self-adhesive abrasive discs. 
• 
Drilling/Boring Accessories - The Mark V comes with a chuck and a chuck key. 
Some also came with a basic set of brad-point bits. 
• 
Turning Accessories - Look for a tailstock, live center, drive center, tool rest, 
and two stop collars (to help position the tailstock in the base). Some machines 
may have come with a basic set of lathe chisels. 
Page 4 of 5 


• 
Support Accessory - The machine should come with one extension table. Note: 
on the Model 520 (introduced in 1991), the width of these table doubled. 
• 
Setup Accessories - A long 5/32” Allen wrench and several shorter allen 
wrenches (4 to 6 wrenches, depending on the model and when the machine was 
made. 
• 
Safety Accessories - In 1973, Mark Vs include safety goggles. 1984, safety 
equipment was expanded to include a push stick, fence straddler, featherboard, 
and push block. 
Page 5 of 5