2:25 AM… The chuck is free!
Rotation, a little winkle with a screw driver, I saw movement. More PB, vertical position, rotation… DONE!
Thanks to all for your aid.
Time … for … bed … zzzzzzzzzzzzzzzzz
Search found 472 matches
- Sat Mar 16, 2013 2:35 am
- Forum: Beginning Woodworking
- Topic: Suggestions to remove a stuck chuck?
- Replies: 75
- Views: 61397
- Fri Mar 15, 2013 9:39 pm
- Forum: Beginning Woodworking
- Topic: Suggestions to remove a stuck chuck?
- Replies: 75
- Views: 61397
Well, thanks for the photos Dusty. You’ve changed my whole outlook. 1- The spindle shaft isn’t quite as long as I’d feared; 2- The chuck may be hollow all the way through. Looked solid when I checked, but I’ll check again for any sign that it’s open on the other end. If so, I’ll definitely lean towa...
- Fri Mar 15, 2013 5:38 pm
- Forum: Beginning Woodworking
- Topic: Suggestions to remove a stuck chuck?
- Replies: 75
- Views: 61397
‘lo Anmius, That idea had occurred to me, but the chuck was really only a tad out of alignment to the flat of the spindle. Maybe enough to cause a problem but, to the naked eye, there didn’t seem to be anything visible in the immediate region… EXCEPT, oddly enough, though the chuck is rotating more ...
- Fri Mar 15, 2013 5:27 pm
- Forum: Beginning Woodworking
- Topic: Rotary PlanerÂ… any experience with them?
- Replies: 7
- Views: 2933
- Fri Mar 15, 2013 3:33 pm
- Forum: Beginning Woodworking
- Topic: Rotary PlanerÂ… any experience with them?
- Replies: 7
- Views: 2933
- Fri Mar 15, 2013 12:37 pm
- Forum: Beginning Woodworking
- Topic: Rotary PlanerÂ… any experience with them?
- Replies: 7
- Views: 2933
Rotary Planer… any experience with them?
Taking a respite from working on this chuck I look around at things that might prove useful to me in the short term. Not seeing myself in a position to purchase a large planer in the immediate future I’ve been noticing rotary planers that I run into here and there. I know that the largest area they ...
- Fri Mar 15, 2013 12:01 pm
- Forum: Beginning Woodworking
- Topic: Suggestions to remove a stuck chuck?
- Replies: 75
- Views: 61397
I’m very sure that the cause of this problem is that the PO, who’d only used it as a drill press for a long while, likely had that chuck connected to the spindle for years. No biggie. These harrowing episodes are requiring me to become more familiar with the machine and to learn more about woodworki...
- Fri Mar 15, 2013 11:58 am
- Forum: Beginning Woodworking
- Topic: Suggestions to remove a stuck chuck?
- Replies: 75
- Views: 61397
- Fri Mar 15, 2013 11:02 am
- Forum: Beginning Woodworking
- Topic: Suggestions to remove a stuck chuck?
- Replies: 75
- Views: 61397
Okay… I WAS able to tap the chuck back up the spindle, but didn’t see much change so far as how far down the spindle it had been in before. After rotating, tapping it back down and rotating again I zapped it with some more PB, put it in the vertical, more PB, rotated and left it to do whatever it ca...
- Fri Mar 15, 2013 11:02 am
- Forum: Beginning Woodworking
- Topic: Suggestions to remove a stuck chuck?
- Replies: 75
- Views: 61397
Okay… I WAS able to tap the chuck back up the spindle, but didn’t see much change so far as how far down the spindle it had been in before. After rotating, tapping it back down and rotating again I zapped it with some more PB, put it in the vertical, more PB, rotated and left it to do whatever it ca...