Dusty,
I have two tables and will set them up this weekend if I get the time. You want diagonal measurements?
Jack
Search found 456 matches
- Sat Dec 12, 2020 9:25 am
- Forum: Community
- Topic: Parallel Extension Tables
- Replies: 86
- Views: 8395
- Tue Nov 10, 2020 7:48 pm
- Forum: Woodworking Tool Review
- Topic: Lift Assist
- Replies: 11
- Views: 3730
Re: Lift Assist
Dido! I have had it on my PowerPro about 5 years. While I could still raise it without the lift I would probably wind up in the ER ;-) I bought a Nova Viking earlier this year so don't anticipate having to raise my Mark V into drill press mode again.
Jack
Jack
- Sat Nov 07, 2020 8:58 am
- Forum: Maintenance and Repair
- Topic: RF interference
- Replies: 9
- Views: 2086
Re: RF interference
I get the static as well. I use a Makita jobsite radio and listen to AM. I attached a piece of thin aluminum wire to my antenna and ran it up the wall until the static disappeared. Problem solved ;-)
Jack
Jack
- Thu Sep 03, 2020 8:42 pm
- Forum: General Woodworking
- Topic: Shopsmith Shaper Origin setup
- Replies: 3
- Views: 2074
Re: Shopsmith Shaper Origin setup
That is pretty darn slick!!! I will have to give that a go soon.
- Sat Aug 22, 2020 10:15 am
- Forum: General Woodworking
- Topic: Router bit Question - Weeker 1/4 Spiral
- Replies: 7
- Views: 3226
Re: Router bit Question - Weeker 1/4 Spiral
That bit is defective. I have one from Whiteside just like it and have routed 30 or 40 feet of hardwood with not a hint of burning. Email Whiteside they will send you a new one. Jack I just purchased an almost identical router bit last week, but mine was from Whiteside. I am used to bearing router b...
- Mon Aug 17, 2020 8:00 am
- Forum: Maintenance and Repair
- Topic: Dedicated Drill Press
- Replies: 22
- Views: 23460
Re: Dedicated Drill Press
In keeping with the tech o my PowerPro here is my dedicated drill press.
Jack
Jack
- Mon Jul 20, 2020 8:17 pm
- Forum: Woodworking Tool Review
- Topic: Rockler Drill Guide
- Replies: 15
- Views: 18131
Re: Rockler Drill Guide
I just checked and their drill guide is in stock and no prohibition against shipping to the US. I wanted the UJK version but they were out of stock forever. A week or so after I ordered the Rockler version the UJK showed up in stock and available for US shipping. The Rockler version is great. Beefy,...
- Sat May 09, 2020 8:12 am
- Forum: Community
- Topic: Deal? DeWalt - 20V MAX XR Brushless Cordless Compact Router
- Replies: 8
- Views: 10172
Re: Deal? DeWalt - 20V MAX XR Brushless Cordless Compact Router
Ed,
I have had the 611 corded version of this router for years and have been very happy with it. I predict you will like this one as well.
Jack
I have had the 611 corded version of this router for years and have been very happy with it. I predict you will like this one as well.
Jack
- Tue Apr 14, 2020 7:18 pm
- Forum: Beginning Woodworking
- Topic: Walking Cane repair & length adjustment
- Replies: 4
- Views: 8102
Re: Walking Cane repair & length adjustment
Great job Glenn! Inquiring minds want to know, what is that laser looking gadget on your Mk V and what is it used for?
Jack
Jack
- Sun Mar 15, 2020 9:42 am
- Forum: Maintenance and Repair
- Topic: PowerPro High Inverter Heat Issue
- Replies: 60
- Views: 62035
Re: PowerPro High Inverter Heat Issue
I have had a DIY PowerPro since not long after they came out. I have never had a heat issue but do not use mine at anything about table speed usually, and then for only short periods. It seems to me that the only change needed by SS is to advertise the potential heat challenge when used at high spee...