Search found 32167 matches

by JPG
Mon Jul 26, 2021 3:58 pm
Forum: Woodworking Tool Review
Topic: RAS safety I might be wrong ??
Replies: 41
Views: 805

Re: RAS safety I might be wrong ??

Let me see here: Pushing(saw contacts the board from the bottom and cuts upward) imparts an upward force on the board and the saw dust exits the kerf at the top of the board at it's yet to be cut edge. Pulling(saw contacts the board from the top and cuts downward) imparts a downward force on the boa...
by JPG
Mon Jul 26, 2021 11:04 am
Forum: Woodworking Tool Review
Topic: RAS safety I might be wrong ??
Replies: 41
Views: 805

Re: RAS safety I might be wrong ??

"And these issues highlight the advantages to a table saw."

Advantage?

Oh there are ways to misuse then also.

However it requires a simple advancement of the work piece towards the blade. Only one set of geometry/vectors likely possible.
by JPG
Mon Jul 26, 2021 10:10 am
Forum: Community
Topic: My Growth Rings with Scott Markwood
Replies: 258
Views: 46749

Re: My Growth Rings with Scott Markwood

:) I would call that glass thingie a "chimney".
by JPG
Mon Jul 26, 2021 9:53 am
Forum: Woodworking Tool Review
Topic: Lithium Screwdriver by WORX
Replies: 3
Views: 69

Re: Lithium Screwdriver by WORX

Would be nice to know where the tiny one originated (i.e.where the granddaughter obtained it).
by JPG
Mon Jul 26, 2021 9:51 am
Forum: Community
Topic: Heads Up - Bargain 'available'
Replies: 2032
Views: 2047093

Re: Heads Up - Bargain 'available'

Appears to include the router.


Go Get it!
by JPG
Mon Jul 26, 2021 9:45 am
Forum: Woodworking Tool Review
Topic: RAS safety I might be wrong ??
Replies: 41
Views: 805

Re: RAS safety I might be wrong ??

I do not see where the nail encounter is improved when pushing rather than pulling. Nor do I see how the out the top is better than out the back as an exit path for the swarf.
by JPG
Sun Jul 25, 2021 9:49 am
Forum: Woodworking Tool Review
Topic: RAS safety I might be wrong ??
Replies: 41
Views: 805

Re: RAS safety I might be wrong ??

This leads us to the question: Why are recent sliding miter saws being 'pushed' rather than 'pulled'? Is it because the blade CAN lift out of the kerf unless held firmly against the workpiece? By 'pushing' .the workpiece is subjected to the lifting force of the blade. +/- Which is worse? I prefer th...
by JPG
Sat Jul 24, 2021 10:35 pm
Forum: Community
Topic: I love my 10ER, but…
Replies: 9
Views: 198

Re: I love my 10ER, but…

:D WHAT? NO Lathe Duplicator?
by JPG
Sat Jul 24, 2021 10:25 pm
Forum: General Woodworking
Topic: Como se llamo esto
Replies: 21
Views: 467

Re: Como se llamo esto

beeg wrote: Sat Jul 24, 2021 1:12 pm

So any new member that posts "off topic", should be disapproved and banned? Replying to an "off topic" doesn't make two wrongs a right. :D So ANY "off topic" post should be deleted?

NO Correct NO

JMHO
by JPG
Sat Jul 24, 2021 8:52 am
Forum: General Woodworking
Topic: Como se llamo esto
Replies: 21
Views: 467

Re: Como se llamo esto

Ohhhh all this consternation about on/off topic. Never an issue for me!(from my perspective) As for the original topic, I am in observe mode re the potential spam. ------------------ Are you off topic ?? :D :D Thought I already said so. :rolleyes: :cool: https://forum.shopsmith.com/viewtopic.php?p=...