Search found 34651 matches
- Tue May 14, 2024 12:12 am
- Forum: Maintenance and Repair
- Topic: 10ER motor spins both ways
- Replies: 2
- Views: 100
Re: 10ER motor spins both ways
I be guessing here (this is a most unusual experience) 1) the motor has a natural tendency to start in one direction when the start circuit is ineffective.(a logical conclusion given the problem) 2) that natural tendency reverses occasionally due to factor(s) unknown. 3) by placing the motor in rota...
- Sun May 12, 2024 4:48 am
- Forum: Community
- Topic: Heads Up - Bargain 'available'
- Replies: 2400
- Views: 3738948
Re: Heads Up - Bargain 'available'
The "holes" in the tube rails are an early model distinction and applies to both the 505 and 510. The early version had tapped holes in the tables thus making them non adjustable.
- Sun May 12, 2024 4:20 am
- Forum: Beginning Woodworking
- Topic: need help, what is thI s
- Replies: 4
- Views: 199
Re: need help, what is thI s
An adapter sleeve works IF one includes a notch for the set screw to fully contact the bit shank. BTDT A bronze bushing bearing seems to have close enough dimensions.
- Tue May 07, 2024 2:55 pm
- Forum: Maintenance and Repair
- Topic: Wax tip.
- Replies: 17
- Views: 18729
Re: Wax tip.
What is needed is carnauba wax. As for scent, that comes from whatever solvents are used. A simpler replacement is paste finishing wax(minwax) JPW was a paste FLOOR wax. Original was slippery so later floor waxes were 'de slipperyiezed'. From looking at the ingredients I would not recommend Jubilee.
- Thu May 02, 2024 5:35 am
- Forum: Community
- Topic: I got a new to me mark
- Replies: 19
- Views: 2711
Re: I got a new to me mark
The black thing sticking out of the mortising attachment (8) is a mortising bit chisel.
- Thu May 02, 2024 5:23 am
- Forum: Maintenance and Repair
- Topic: Motor Re-Wire to reverse spin
- Replies: 1
- Views: 118
Re: Motor Re-Wire to reverse spin
The start circuit consists of the start winding in series with the start switch and start capacitor. The ends of that series circuit attaches to the run windings and power cord. Reversing the start circuit end connections will cause the motor to run in the opposite direction. However there appears t...
- Sun Apr 28, 2024 10:16 pm
- Forum: Maintenance and Repair
- Topic: 10ER Speed changer motor offset?
- Replies: 3
- Views: 262
Re: 10ER Speed changer motor offset?
I think a picture of what you have would help.
- Sun Apr 28, 2024 4:43 pm
- Forum: Maintenance and Repair
- Topic: Quill coupler broken - where to source new part?
- Replies: 19
- Views: 2287
Re: Quill coupler broken - where to source new part?
AIRI,Considerable force IS required to get the sleeve installed onto the shaft. It would be best to backup the rear end of the shaft while applying any impact or force to the sleeve so the bearings are isolated.
- Fri Apr 26, 2024 7:09 pm
- Forum: Maintenance and Repair
- Topic: Loose Drive Assembly where Tool Attach
- Replies: 3
- Views: 849
Re: Loose Drive Assembly where Tool Attach
Assuming the 'knurled' collar is attached correctly, the drill chuck is NOT. The set screws should line up. Also potential play is reduced by rocking the item being attached as the set screw is tightened. This centers the set screw at the low point of the shaft flat.
- Tue Apr 23, 2024 10:07 pm
- Forum: General Woodworking
- Topic: Apprenticeship
- Replies: 4
- Views: 1611
Re: Apprenticeship
Good Luck finding a youngster interested in that path.