Search found 34648 matches
- Tue May 07, 2024 2:55 pm
- Forum: Maintenance and Repair
- Topic: Wax tip.
- Replies: 17
- Views: 18680
Re: Wax tip.
What is needed is carnauba wax. As for scent, that comes from whatever solvents are used. A simpler replacement is paste finishing wax(minwax) JPW was a paste FLOOR wax. Original was slippery so later floor waxes were 'de slipperyiezed'. From looking at the ingredients I would not recommend Jubilee.
- Thu May 02, 2024 5:35 am
- Forum: Community
- Topic: I got a new to me mark
- Replies: 19
- Views: 2195
Re: I got a new to me mark
The black thing sticking out of the mortising attachment (8) is a mortising bit chisel.
- Thu May 02, 2024 5:23 am
- Forum: Maintenance and Repair
- Topic: Motor Re-Wire to reverse spin
- Replies: 1
- Views: 107
Re: Motor Re-Wire to reverse spin
The start circuit consists of the start winding in series with the start switch and start capacitor. The ends of that series circuit attaches to the run windings and power cord. Reversing the start circuit end connections will cause the motor to run in the opposite direction. However there appears t...
- Sun Apr 28, 2024 10:16 pm
- Forum: Maintenance and Repair
- Topic: 10ER Speed changer motor offset?
- Replies: 3
- Views: 239
Re: 10ER Speed changer motor offset?
I think a picture of what you have would help.
- Sun Apr 28, 2024 4:43 pm
- Forum: Maintenance and Repair
- Topic: Quill coupler broken - where to source new part?
- Replies: 17
- Views: 1646
Re: Quill coupler broken - where to source new part?
AIRI,Considerable force IS required to get the sleeve installed onto the shaft. It would be best to backup the rear end of the shaft while applying any impact or force to the sleeve so the bearings are isolated.
- Fri Apr 26, 2024 7:09 pm
- Forum: Maintenance and Repair
- Topic: Loose Drive Assembly where Tool Attach
- Replies: 3
- Views: 697
Re: Loose Drive Assembly where Tool Attach
Assuming the 'knurled' collar is attached correctly, the drill chuck is NOT. The set screws should line up. Also potential play is reduced by rocking the item being attached as the set screw is tightened. This centers the set screw at the low point of the shaft flat.
- Tue Apr 23, 2024 10:07 pm
- Forum: General Woodworking
- Topic: Apprenticeship
- Replies: 4
- Views: 1436
Re: Apprenticeship
Good Luck finding a youngster interested in that path.
- Tue Apr 23, 2024 10:06 am
- Forum: Maintenance and Repair
- Topic: Double tilt upgrade
- Replies: 12
- Views: 1904
Re: Double tilt upgrade
I be guilty of overlooking that obvious detail! ;>{
- Mon Apr 22, 2024 10:15 pm
- Forum: Maintenance and Repair
- Topic: Double tilt upgrade
- Replies: 12
- Views: 1904
Re: Double tilt upgrade
The shims are placed against the SIDES of the tubes. The tube clamp exerts outward pressure to the tubes. The final position is determined by a small boss extending out from the outer interior surface of the end casting. The shims essentially make that boss longer. The shims are necessary since his ...
- Mon Apr 22, 2024 10:05 pm
- Forum: Maintenance and Repair
- Topic: removing speed control handle
- Replies: 3
- Views: 6202
Re: removing speed control handle
CAREFULLY pry around the outer edge at multiple locations a smidgen at a time. You may need to simultaneously pry diametrically opposed to prevent cocking.