I would have to measure that too. Since the 10" diameter center disk of the Universal Lathe Tool Rest is wider than the carriage at least some of the upper mounting bracket of the Lift Assist would be under the 10" center Disk.
FYI the column turning video is impressive.
Search found 3479 matches
- Wed Apr 17, 2024 12:26 pm
- Forum: Woodworking Tool Review
- Topic: Universal Lathe Tool Rest min spindle length
- Replies: 5
- Views: 449
- Tue Apr 16, 2024 1:37 pm
- Forum: Community
- Topic: Mark v speed controller problem
- Replies: 4
- Views: 182
Re: Mark v speed controller problem
Majjr, Welcome to the Shopsmith Forum. I have not had that problem. That is a sealed Bearing and should not need oiling. Over time sealed bearings will "wear" out which does happen. I have to wonder where you are getting your replacements from. Shopsmith only sells it installed in the Floa...
- Tue Apr 16, 2024 1:13 pm
- Forum: Maintenance and Repair
- Topic: New Owner to 2 Shopsmiths
- Replies: 3
- Views: 126
Re: New Owner to 2 Shopsmiths
Ciggy, Welcome to the Shopsmith Forum. Congratulations on the great find. As Ed has already said Tailstocks are all interchangeable. All Mark 5/V's be it a 500, 510/505, 520, 520S, Mark 7 or Mark 4 all use the same Tailstock which has been basically the same since the introduction of the Mark 5 in 1...
- Tue Apr 16, 2024 12:49 pm
- Forum: Woodworking Tool Review
- Topic: Universal Lathe Tool Rest min spindle length
- Replies: 5
- Views: 449
Re: Universal Lathe Tool Rest min spindle length
I can't tell you without going out to the shop, mounting my Universal Lathe Tool Rest on my Mark and getting actual measurements. For a little math work the main part to the equation is the center disk measuring 10" in diameter. That's how far apart the Headstock will be from the Tailstock. Sub...
- Tue Apr 16, 2024 12:24 pm
- Forum: General Woodworking
- Topic: Which Lathe upgrade?
- Replies: 15
- Views: 1289
Re: Which Lathe upgrade?
gkillebrew, Welcome to the Shopsmith Forum. Below is a picture of a Lathe Tool Rest Assembly from a Mark V made in March 1982. This is from the original Table System later refered to as the Mark V 500. _ Lathe Tool Rest 03-82.jpg . They have the "threaded" Post and a shorter Arm than the o...
- Mon Apr 15, 2024 4:44 pm
- Forum: Maintenance and Repair
- Topic: New Owner
- Replies: 21
- Views: 1193
Re: New Owner
This is what that flat spring looks like in position as shown in the picture below. It is the part under the arrow not what the arrow is pointing to. Sorry it's the only picture I could find of it right now.
_
_
- Mon Apr 15, 2024 12:59 pm
- Forum: Maintenance and Repair
- Topic: New Owner
- Replies: 21
- Views: 1193
Re: New Owner
That is a lot of wear on that Gilmer Drive Sleeve Assembly. I don't know why the belt would wear it down so much through normal use even considering its age. If the Bearings are not turning smoothly, they should be replaced. Poorly turning bearings will rob power between the motor and Quill. You may...
- Mon Apr 15, 2024 12:35 pm
- Forum: General Woodworking
- Topic: Which Lathe upgrade?
- Replies: 15
- Views: 1289
Re: Which Lathe upgrade?
At $50 off this is probably the best deal you will find on the Speed Reducer from Shopsmith.
- Sun Apr 14, 2024 12:11 pm
- Forum: Maintenance and Repair
- Topic: Quill coupler broken - where to source new part?
- Replies: 8
- Views: 334
Re: Quill coupler broken - where to source new part?
danielsegge, Welcome to the Shopsmith Forum. As you may have guessed from the posts from other members it makes a difference which drive system your Shopsmith Mark 5 has. Mark 5 Greenies which started in 1954 through Goldies made prior to mid 1961 originally came with the Gilmer Drive while all Mark...
- Fri Apr 12, 2024 12:58 pm
- Forum: Maintenance and Repair
- Topic: How do you really feel about the term "Smart Motor"?
- Replies: 10
- Views: 464
Re: How do you really feel about the term "Smart Motor"?
Thanks to all of you who have added their thoughts here so far. I would like to add to my opinion about the term "Smart Motor." Calling either the Conventional or Power Pro Headstock only "Smart Motor" tends to leave out the other functions and parts of either Headstock. The Quil...