Search found 3486 matches
- Mon Apr 22, 2024 1:59 pm
- Forum: Community
- Topic: I got a new to me mark
- Replies: 7
- Views: 222
Re: I got a new to me mark
youngstev, Welcome to the Shopsmith Forum. Thank you for adding the pictures. They are a great help in describing things. Shopsmith Mark 5 serial number SS 9405 would have likely been made in 1975. There are no records from that time period, so it is an estimate I have made. Hopefully included in th...
- Mon Apr 22, 2024 12:29 pm
- Forum: Maintenance and Repair
- Topic: Double tilt upgrade
- Replies: 7
- Views: 213
Re: Double tilt upgrade
Hami5297, First off, welcome to the Shopsmith Forum. Below is the information given on the Double Tilt Upgrade online catalog page. Note: For MARK V 520, 510, 505 / MARK 4 Only -- The MARK V 500 does not have interchangeable table support tubes. Note: Older MARK V 500 machines (produced before 1972)...
- Sun Apr 21, 2024 12:19 pm
- Forum: Maintenance and Repair
- Topic: Quill coupler broken - where to source new part?
- Replies: 13
- Views: 595
Re: Quill coupler broken - where to source new part?
David you are correct. The one in yesterday's post is, I believe an older version. The one on a Drive Sleeve Assembly below is like the one you show. _ Drive Sleeve Assembly - Poly V with Drive and Ring.jpg . I believe I have a spare like the one shown above I bought from Shopsmith not too long ago....
- Sat Apr 20, 2024 1:12 pm
- Forum: Maintenance and Repair
- Topic: Quill coupler broken - where to source new part?
- Replies: 13
- Views: 595
Re: Quill coupler broken - where to source new part?
The Drive & Ring Assembly attaches to the end of the Drive Sleeve Assembly and is the plastic drive part with a metal ring inside. That metal ring holds the drive on the splined end of the Drive Sleeve Assembly by "snapping" into the indents in the splines. You can see those indents on...
- Sat Apr 20, 2024 12:58 pm
- Forum: Maintenance and Repair
- Topic: New Shopsmith Owner
- Replies: 81
- Views: 20708
Re: New Shopsmith Owner
When I said, Parts for these old Model A-34 Jig Saws do come up for sale occasionally. I didn't want to give you false hope as those parts could come up for sale next week or next year or later. It is hard to tell when it may show up. As for making a replacement, the Hold Down Lock Cylinder P/N 134-...
- Fri Apr 19, 2024 12:44 pm
- Forum: Maintenance and Repair
- Topic: New Shopsmith Owner
- Replies: 81
- Views: 20708
Re: New Shopsmith Owner
Briansmith91, Those parts, 134-34 and 134-23, are very specific to the very old Jig Saw made for the Model 10E and 10ER. The Washer P/N 134-34W is pretty common hardware. Unless you or someone can make them for you, you would have to find them on the used market. Parts for these old Model A-34 Jig S...
- Thu Apr 18, 2024 12:53 pm
- Forum: Woodworking Tool Review
- Topic: Universal Lathe Tool Rest min spindle length
- Replies: 7
- Views: 779
Re: Universal Lathe Tool Rest min spindle length
I got out to the shop yesterday afternoon and did some measuring. It was without the actual Universal Lathe Tool Rest since I have not found it yet since moving. Still too many unorganized boxes of "stuff" around the shop. Using the different Tailstock Centers I have about 2" to 4&quo...
- Wed Apr 17, 2024 12:26 pm
- Forum: Woodworking Tool Review
- Topic: Universal Lathe Tool Rest min spindle length
- Replies: 7
- Views: 779
Re: Universal Lathe Tool Rest min spindle length
I would have to measure that too. Since the 10" diameter center disk of the Universal Lathe Tool Rest is wider than the carriage at least some of the upper mounting bracket of the Lift Assist would be under the 10" center Disk.
FYI the column turning video is impressive.
FYI the column turning video is impressive.
- Tue Apr 16, 2024 1:37 pm
- Forum: Community
- Topic: Mark v speed controller problem
- Replies: 4
- Views: 389
Re: Mark v speed controller problem
Majjr, Welcome to the Shopsmith Forum. I have not had that problem. That is a sealed Bearing and should not need oiling. Over time sealed bearings will "wear" out which does happen. I have to wonder where you are getting your replacements from. Shopsmith only sells it installed in the Floa...
- Tue Apr 16, 2024 1:13 pm
- Forum: Maintenance and Repair
- Topic: New Owner to 2 Shopsmiths
- Replies: 3
- Views: 181
Re: New Owner to 2 Shopsmiths
Ciggy, Welcome to the Shopsmith Forum. Congratulations on the great find. As Ed has already said Tailstocks are all interchangeable. All Mark 5/V's be it a 500, 510/505, 520, 520S, Mark 7 or Mark 4 all use the same Tailstock which has been basically the same since the introduction of the Mark 5 in 1...