Search found 182 matches

by WileyCoyote
Sun Jun 13, 2021 10:09 pm
Forum: Maintenance and Repair
Topic: GFCI Issues
Replies: 11
Views: 534

Re: GFCI Issues

Yes, it was on the load side but with nothing plugged into the outlet. Until I get the new GFCI in I will continue to use the GFCI as a dedicated outlet for the Shopsmith. My second Shopsmith would normally be plugged into the outlet on the load side.
by WileyCoyote
Sun Jun 13, 2021 7:27 pm
Forum: Maintenance and Repair
Topic: GFCI Issues
Replies: 11
Views: 534

Re: GFCI Issues

I see they have a Leviton Hospital grade 20A for $22.53 on Amazon. I will probably try that. Still makes no sense that the second outlet causes some type of interference that cause it to trip. The GFCI is working fine with nothing else associated with it, no nuisance trips at all.
by WileyCoyote
Sun Jun 13, 2021 5:23 pm
Forum: Maintenance and Repair
Topic: GFCI Issues
Replies: 11
Views: 534

Re: GFCI Issues

Yes, the two from the breaker went to the line in and the two to the outlet went to the load. The two grounds were tied together and connected to the ground screw.
by WileyCoyote
Sun Jun 13, 2021 3:15 pm
Forum: Maintenance and Repair
Topic: GFCI Issues
Replies: 11
Views: 534

GFCI Issues

I had a visit from my brother-in-law over the holidays and I allowed him to plug his motorhome into what I thought was a dedicated 20A circuit. I have been using this circuit for years with my two Shopsmiths and the moment he plugged in, tripped a 15A GFCI a little farther down the wall. Bewildered,...
by WileyCoyote
Sat Mar 28, 2020 8:09 am
Forum: Beginning Woodworking
Topic: Finally Snops it’s posts on YouTube.
Replies: 22
Views: 25571

Re: Finally Snops it’s posts on YouTube.

I got to meet him some years ago when they still had their showroom in Dayton. I thought I saw somewhere that he was still doing demos. I am sure in his career he made hundreds of these all around the country and probably still does.
by WileyCoyote
Sun Mar 22, 2020 4:37 am
Forum: Community
Topic: Support your local businesses
Replies: 2
Views: 4547

Support your local businesses

We had planned a trip to Lowes yesterday and on the way my wife had a great idea. Why don't we go to Ace Hardware and support a local company. I told her usually the prices are not comparable to the big box stores. We walked into Ace and three employees greeted us at the door. They offered us saniti...
by WileyCoyote
Sat Mar 07, 2020 5:34 am
Forum: Community
Topic: Possible mark V prototype?
Replies: 11
Views: 15667

Re: Possible mark V prototype?

Russ, I saw this on the Facebook Shopsmith Owners Board this morning. This is the oldest I have seen an actual photo of.
by WileyCoyote
Sun Mar 01, 2020 6:30 am
Forum: Woodworking Tool Review
Topic: SHOP SMITH TABLE IDENTIFICATION
Replies: 23
Views: 47485

Re: SHOP SMITH TABLE IDENTIFICATION

My greenie is Mar 55, (SN# 291904) and has the single slot. Any "newer" 55's out there that can chime in?
by WileyCoyote
Thu Feb 27, 2020 3:47 pm
Forum: General Woodworking
Topic: Need Suggestions on making a display item
Replies: 8
Views: 9045

Re: Need Suggestions on making a display item

I kept reading, and rereading your post and kept thinking, "What birds is he talking about?" After opening your attachment they became clear. What program did you use to convert the image to an outline?
by WileyCoyote
Thu Feb 27, 2020 8:57 am
Forum: Woodworking Tool Review
Topic: Router Raizer Install
Replies: 8
Views: 11713

Re: Router Raizer Install

I found the wrenches on Amazon, too. It came with both ER16 and ER20 wrenches for less than $10.00 https://www.amazon.com/gp/product/B083XZ2KRH/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 I tried it out last night and I noticed no noticeable vibrations at all. I only routed a piece of pine ...