Search found 628 matches
- Tue Jul 25, 2023 12:07 am
- Forum: Maintenance and Repair
- Topic: Miter-Pro Manual
- Replies: 3
- Views: 1632
Re: Miter-Pro Manual
Part 845246, according to the SS web site. They show a cost of $5.99...probably some additional for shipping.
- Sat Jul 22, 2023 10:35 pm
- Forum: Community
- Topic: Help me give away a Shopsmith?
- Replies: 14
- Views: 5093
Re: Help me give away a Shopsmith?
I have a tailstock for the 500 I would enjoy contributing. Where to send it?
- Fri Jul 07, 2023 1:17 pm
- Forum: Community
- Topic: Using a Shop Smith Mark V on a Chris Craft Roamer refit
- Replies: 877
- Views: 1421125
Re: Using a Shop Smith Mark V on a Chris Craft Roamer refit
roamer 46;
That is an impressive rebuild of an impressive boat! Thanks for the video from the helm...looks like its a lot of fun to pilot that beauty! Congratulations on carrying such a large project through to an amazing finish.
That is an impressive rebuild of an impressive boat! Thanks for the video from the helm...looks like its a lot of fun to pilot that beauty! Congratulations on carrying such a large project through to an amazing finish.
- Wed Jul 05, 2023 12:33 am
- Forum: Maintenance and Repair
- Topic: Carriage Stop Ring for Mk V 500
- Replies: 11
- Views: 3245
Re: Carriage Stop Ring for Mk V 500
The carriage on my 500 is from an old Greenie, and it is threaded on the side facing the headstock for a stop bolt which does the same job the spacer ring does. The stop bolt is adjusted to provide the correct spacing, then locked down with a nut. Stop Bolt Photo.jpg Maybe your old carriage is threa...
- Sat Jul 01, 2023 8:25 pm
- Forum: Community
- Topic: Dating a Mark 5 by it's serial number.
- Replies: 3
- Views: 1248
Re: Dating a Mark 5 by it's serial number.
Hi Midwest Preacher;
Here is a chart that gives serial numbers and approximate dates, but it does not seem to help with identifying the date of your machine. JPG is correct, more information and a picture or two would help.
Here is a chart that gives serial numbers and approximate dates, but it does not seem to help with identifying the date of your machine. JPG is correct, more information and a picture or two would help.
- Tue Jun 20, 2023 10:21 pm
- Forum: General Woodworking
- Topic: Great Idea or Just Madness...
- Replies: 47
- Views: 26012
Re: Great Idea or Just Madness...
Interesting idea! The hardware will be the critical part. That 'whitewood' resembles spruce. I agree...a VERY interesting idea. That will be a lot of weight, though, so the hardware may turn out to be some sort of roller bearings and not just oversize lazy susan hardware. Maybe an opportunity for s...
- Sun May 28, 2023 11:10 pm
- Forum: Beginning Woodworking
- Topic: shop built crosscut sled for ShopSmith
- Replies: 20
- Views: 8981
Re: shop built crosscut sled for ShopSmith
its a beauty!
- Tue May 16, 2023 5:24 pm
- Forum: General Woodworking
- Topic: This dont feel right..
- Replies: 6
- Views: 4921
Re: This dont feel right..
I think using a SS push block to put some down pressure on the piece as you feed it might make the operation feel more secure, and the block should keep the fingers far enough away just in case something goes awry. Or you could try wrapping sandpaper around a dowel of the right radius and do it the ...
- Sun May 14, 2023 11:30 pm
- Forum: General Woodworking
- Topic: Lap Tray for Mother's Day
- Replies: 6
- Views: 3066
Re: Lap Tray for Mother's Day
very nice!
- Mon May 08, 2023 2:00 pm
- Forum: General Woodworking
- Topic: Three Deminsional Eight Pointed Srar
- Replies: 26
- Views: 9954