Search found 20 matches
- Sun Nov 07, 2021 8:08 am
- Forum: General Woodworking
- Topic: It's news to me
- Replies: 10
- Views: 3376
Re: It's news to me
that nice, the poly only was a good choice, looks very good
- Tue Nov 02, 2021 1:59 pm
- Forum: Beginning Woodworking
- Topic: SS Mark 7, Lathe and Routing
- Replies: 27
- Views: 9682
Re: SS Mark 7, Lathe and Routing
Yes, pens can be done on a Shopsmith. And other small things also. If you buy a chuck you will have to get a SS adaptor for the chuck.DSC00912.JPGtrifecta.JPG Bill V Bill: some very nice work sir, i hope with alot of practice i can do close to that quality has anyone used or own the SS Nova penset ...
- Tue Nov 02, 2021 1:55 pm
- Forum: Maintenance and Repair
- Topic: vertical trueness
- Replies: 23
- Views: 2528
Re: vertical trueness
just wanted to say thank you to everyone, it really wasnt a major deal. the table, quill and everything else is checking fine, was more of a observation but i did go over the links and suggestion and i do appreciate eveyones time.
- Mon Nov 01, 2021 8:40 am
- Forum: General Woodworking
- Topic: Eagle Head
- Replies: 9
- Views: 2311
Re: Eagle Head
thats real nice work,
- Sun Oct 31, 2021 5:10 pm
- Forum: Maintenance and Repair
- Topic: vertical trueness
- Replies: 23
- Views: 2528
Re: vertical trueness
the tubes in the upright are just shy of 90 about 1/2 a bubble and the same on the other end in the upright, but in the horizontal she is dead true, and the table to quill is true, every other item i have checked so far has been close as possible.
- Sun Oct 31, 2021 4:06 pm
- Forum: Maintenance and Repair
- Topic: vertical trueness
- Replies: 23
- Views: 2528
Re: vertical trueness
Troy, This is a looong thread linked below, but it discusses what you are asking, I believe. By the way, there was A LOT of confusion on this thread until everyone understood what was being discussed. Hope this helps. https://forum.shopsmith.com/viewtopic.php?p=287868#p287868 By the way, you can re...
- Sun Oct 31, 2021 3:18 pm
- Forum: Maintenance and Repair
- Topic: vertical trueness
- Replies: 23
- Views: 2528
vertical trueness
i have been going slow with the new "used mk 7" haven't had alot of free time. i started off checking alignment and discovered that several of the leg bolts, lift assist bolts and caster bolts were not real tight, so i backed off went to step one off install and setup, everything is fallin...
- Thu Oct 14, 2021 8:49 pm
- Forum: General Woodworking
- Topic: Front Door Refresh
- Replies: 14
- Views: 4779
Re: Front Door Refresh
looks fantastic, id be proud of that
- Wed Oct 13, 2021 4:22 pm
- Forum: Beginning Woodworking
- Topic: First project with new/old Mv5
- Replies: 12
- Views: 5890
Re: First project with new/old Mv5
looks good,
- Mon Oct 11, 2021 7:43 pm
- Forum: Beginning Woodworking
- Topic: Webinar
- Replies: 4
- Views: 3378
Webinar
Has anyone done one of mr reids or the ShopSmith webinars ? and approximately how long do they last, how much bandwidth is needed? and is a mic & Cam needed ??
we are out in the rural and my internet drifts between 5 meg and 11 meg down "a real good day".
thanks
we are out in the rural and my internet drifts between 5 meg and 11 meg down "a real good day".
thanks