Search found 34645 matches
- Fri Dec 19, 2008 12:24 am
- Forum: Woodworking Tool Review
- Topic: Headstock Rebuild
- Replies: 18
- Views: 29483
headstock rebuild
Sure they do! Makes sense if you reside in OHIO! I believe the thread starter resides in WASHINGTON! That is quite a few more miles to pay shipping on. Pay attention to what Bill Mayo said. The task is not really that difficult (sometimes maddening however) if you have the tools listed. Only slightl...
- Thu Dec 18, 2008 1:56 am
- Forum: Beginning Woodworking
- Topic: Conical Disk
- Replies: 32
- Views: 25080
Sand Paper Disk Removal
I HAVE NOT TRIED THIS, BUT, IF "HOT WATER" WORKS, I WOULD THINK A HEAT LAMP WOULD ALSO. IF PAPER IS KEPT DRY IT COULD PROBABLY BE REUSED.
SOMEBODY TRY IT & TELL US IF IT WORKS!!!
SOMEBODY TRY IT & TELL US IF IT WORKS!!!
- Tue Dec 16, 2008 7:13 pm
- Forum: Community
- Topic: ShopSmith Order filling Shortcoming.. Again!
- Replies: 157
- Views: 91235
Swmbo
Thanks! We can ALWAYS learn something new if we only try/ask!;)
- Tue Dec 16, 2008 6:19 pm
- Forum: Community
- Topic: ShopSmith Order filling Shortcoming.. Again!
- Replies: 157
- Views: 91235
Swmbo????
[quote="dusty"]I have listened and I have heard. Everyone seems to be having trouble getting orders filled. Now I will find out for myself.
I just placed my Santa order for stocking stuffers]
Pardon my ignorance: but, what is a SWMBO?????
I just placed my Santa order for stocking stuffers]
Pardon my ignorance: but, what is a SWMBO?????
- Tue Dec 16, 2008 6:08 pm
- Forum: Maintenance and Repair
- Topic: 510 table surface polishing
- Replies: 10
- Views: 29052
rust removal
LOOK in SHOP TIPS for ..rust removal using potato.. NO I am not kidding! Nick shows us how to remove rust from way/support tubes using... 4"pvc sewer pipe/fittings, water, and a potatoe. Takes weeks to work, BUT it does WORK. It also creates raw material for magnetic tape. It would also work(di...
- Tue Dec 16, 2008 4:34 pm
- Forum: Community
- Topic: ShopSmith Order filling Shortcoming.. Again!
- Replies: 157
- Views: 91235
BO
:eek: Well goes my "contribution" to this thread. We all need to keep in our mind the desire of all of us to have a source of SS parts (other than somebody elses sometimes worn out also from ebay/craigs list ...:D ). Our benefactor (SS) IS once again upon difficult times (last October they...
- Tue Dec 16, 2008 3:57 pm
- Forum: Maintenance and Repair
- Topic: jointer
- Replies: 14
- Views: 37273
Jointer chip departure
What is a "vac system"? Thought they are for "SAWDUST"!!! I do not have a vac system, therefore all my jointer "chips" exit out from under the cutter (it is WIDE open down there). Perhaps you have a "vac system" part under there with no "vac" attache...
- Sun Dec 14, 2008 4:02 pm
- Forum: General Woodworking
- Topic: Speed Control and Frightening Noises
- Replies: 33
- Views: 56021
Sheaves = Control / Drive
If you look back at Nick's post you will notice the words "DRIVE SHEAVES" when referring to 1/16 ...1/8 inch dimension below outer rim of sheaves depicted in picture....You can notice the end of motor housing!! Compare this pix to that of "CONTROL SHEAVES" in previous pix. The UP...
Farewell.....Return SOON!!!!
NICK!! Do not CHANGE too much. Thanks for past "HELP" GOOD LUCK!!!!!!!!!!
- Fri Dec 12, 2008 7:18 pm
- Forum: General Woodworking
- Topic: Rpm
- Replies: 68
- Views: 34030