Good Morning,
When you get a chance would you send, cjcvontrappmeyer@aol.com or post a few pics of your 520 augmented with 510 extension table/s? Thanks
Search found 85 matches
- Mon May 25, 2020 10:19 am
- Forum: Beginning Woodworking
- Topic: Shopsmith 520 ext tables
- Replies: 20
- Views: 25420
- Sat May 23, 2020 5:43 pm
- Forum: Beginning Woodworking
- Topic: Shopsmith 520 ext tables
- Replies: 20
- Views: 25420
Re: Shopsmith 520 ext tables
Ok, after reviewing all of the photos from the URL you sent, I see the upright posts attached to a table which I conclude makes it a fixed component. Also, are the metal legs of no use to me with the current system? Should I consider selling the two 510 tables with the metal posts/legs? Am I correct...
- Sat May 23, 2020 5:02 pm
- Forum: Beginning Woodworking
- Topic: Shopsmith 520 ext tables
- Replies: 20
- Views: 25420
Re: Shopsmith 520 ext tables
Thank you for taking the time to respond to my inquiries. I don't understand your question, "You should also have a fixed extension table with legs that fits in the holes in the end castings. What type of rails does it have? " I don't have any other tables. Please reword the question or po...
- Sat May 23, 2020 3:25 pm
- Forum: Beginning Woodworking
- Topic: Shopsmith 520 ext tables
- Replies: 20
- Views: 25420
Re: Shopsmith 520 ext tables
The floating tables with the extruded rails is what I am going to purchase. Are the tables without extrusions, 510 tables? If I understand, the unextruded tables are of no use to me with the present extruded tablesaw configuration. I can use the tubes but not the mix of tables because of inconsisten...
- Fri May 22, 2020 6:52 pm
- Forum: Beginning Woodworking
- Topic: Shopsmith 520 ext tables
- Replies: 20
- Views: 25420
Shopsmith 520 ext tables
I have a 520 tablesaw upgrade but the extension tables are 510 extension tables, I think. Is there a benefit in acquiring 520 extension tables?
- Wed May 20, 2020 11:21 am
- Forum: Beginning Woodworking
- Topic: Face Plates??
- Replies: 8
- Views: 10213
Re: Face Plates??
ok, where did you get the food grade safe materials to make the bowl?
- Wed May 20, 2020 12:04 am
- Forum: Beginning Woodworking
- Topic: Face Plates??
- Replies: 8
- Views: 10213
Re: Face Plates??
that is a beautiful bowl! Please tell me how you achieve those results, step by step!
- Tue May 19, 2020 11:23 pm
- Forum: Beginning Woodworking
- Topic: Face Plates??
- Replies: 8
- Views: 10213
Face Plates??
Understand, I don't have a clue as to what a face plate is used for, all I know is I have four of them. Keep in mind, that I am a newbie!! I have two 6 inch face plates and two smaller face plates. What are they used for? does the steel face place offer an advantage that the aluminum face plate does...
- Tue May 19, 2020 5:58 pm
- Forum: Beginning Woodworking
- Topic: Shopsmith Crosscut Sled
- Replies: 22
- Views: 29444
Shopsmith Crosscut Sled
Does anyone on this forum use the sled? If so, how are the holes used during operation and is it a worthwhile addition to the Shopsmith? The photos are screen shots. The Shopsmith website doesn't show the face of the sled so it's difficult for me to know if these are predrilled during the manufactur...
- Wed May 13, 2020 9:14 am
- Forum: Maintenance and Repair
- Topic: Molder Head Knives old/new
- Replies: 2
- Views: 4684
Re: Molder Head Knives old/new
I went back to the page with my quote and saw where both the old and new styles were available for purchase. I was blind but now I see. Thanks!