Search found 6410 matches
- Sat Oct 17, 2015 8:18 pm
- Forum: General Woodworking
- Topic: For you digital gauge guys
- Replies: 22
- Views: 9270
Re: For you digital gauge guys
Hmmm! Since I use a piece of MDF on top of the table, along with the coat hanger, a feeler gauge would come in handy. Thanks, John! :D Concerning tilt side to side (front to back in the saw mounting) it can be fixed in drill press configuration. Such a side to side test should be a must have for th...
- Sat Oct 17, 2015 8:05 pm
- Forum: Beginning Woodworking
- Topic: Sunset Potting Bench
- Replies: 7
- Views: 7752
Re: Sunset Potting Bench
That really looks nice. Good job!!!
- Sat Oct 17, 2015 8:00 pm
- Forum: Beginning Woodworking
- Topic: My first SS project - patio fence
- Replies: 11
- Views: 8985
Re: My first SS project - patio fence
I am totally with you on that. #0000 steel wool works to knock down a glossy finish also.charlese wrote:My tastes run toward satin finishes.
If I use a glossy finish, a bit of sanding will remove the shine and take it down to semi gloss or satin.
- Fri Oct 16, 2015 9:45 pm
- Forum: General Woodworking
- Topic: For you digital gauge guys
- Replies: 22
- Views: 9270
Re: For you digital gauge guys
I have a brand spankety new feeler gauge to go with it.JPG wrote:charlese wrote:FWIW - A bent coat hanger put into the chuck works good too
It 'calibrated' in 0.001"?
- Fri Oct 16, 2015 5:29 pm
- Forum: Community
- Topic: W10 Cuestion
- Replies: 9
- Views: 554
Re: W10 Cuestion
Oh OK. The main screen in W7 is the same. No hint of it either.JPG wrote:jsburger wrote:So are yoy saying it is not there in W10?
Oh it IS there, just no clue of that on the main screen of Control Panel.
- Fri Oct 16, 2015 5:00 pm
- Forum: Community
- Topic: W10 Cuestion
- Replies: 9
- Views: 554
Re: W10 Cuestion
So are yoy saying it is not there in W10?
- Fri Oct 16, 2015 4:38 pm
- Forum: Community
- Topic: W10 Cuestion
- Replies: 9
- Views: 554
Re: W10 Cuestion
JPG wrote:Where/How does one manually define file name extension(type) associations?
To overcome presumptuous new software installation.
I don't know how much W10 changed but in W7 it is under Control Panel-Programs-Default Programs-Set Associations.
- Thu Oct 15, 2015 7:53 pm
- Forum: Community
- Topic: A Source For Hardware
- Replies: 15
- Views: 1969
Re: A Source For Hardware
Folks, the intent of my post wasn't to get anyone to stop shopping at their favorite local hardware supplier but just to let folks who don't have access to one know that there's a good internet supplier out there. You are correct. I urge everyone to buy local if you can. When I first got here in Ut...
- Thu Oct 15, 2015 7:35 pm
- Forum: Maintenance and Repair
- Topic: AO Smith motor rebuild
- Replies: 45
- Views: 6348
Re: AO Smith motor rebuild
You will likely find that spring behind most bearings(even the belt sander). It presses against the outer race to allow slight movement as the temperature changes or from any other 'need'. The motor output shaft end is typically solid. I question the lack of that spring to be 'the culprit'. I am un...
- Thu Oct 15, 2015 5:17 pm
- Forum: Community
- Topic: A Source For Hardware
- Replies: 15
- Views: 1969
Re: A Source For Hardware
We have Ace Hardware stores here. If you can't find it anywhere else Ace will probably have it. Especially in the hardware department.
Maybe they should bring back the old Connie Stevens adds.
Maybe they should bring back the old Connie Stevens adds.