Search found 6396 matches
- Sun Mar 03, 2024 7:13 pm
- Forum: Community
- Topic: Looking For Dinner
- Replies: 2
- Views: 318
Looking For Dinner
We had a visitor at the bird feeder today looking for dinner. The feeder is about 10' to the right. A little out of focus because they were taken through the sliding door.
- Sat Mar 02, 2024 6:57 pm
- Forum: Community
- Topic: Utah Winter Sunsets
- Replies: 69
- Views: 640524
Re: Utah Winter Sunsets
Not a sunset but a late winter storm. The high this morning was 55°. It is now (5PM) 31°. The wind was ferocious as the cold front approached. There was a gust of 55MPH here at the house and the 10 minute average was 30MPH most of the morning. Now the anemometer is frozen because it started out as r...
- Mon Feb 26, 2024 9:19 pm
- Forum: Community
- Topic: Cateract Surgery
- Replies: 12
- Views: 965
Cateract Surgery
The VA provides me with vision care and eye glasses. I have been going to the Salt Lake VA regional medical center for 28 years.Over the years they have monitored me for Glaucoma and provided me with glasses. I don't have Glaucoma but my cataracts have been getting worse over the last 2 or 3 years. ...
- Mon Feb 26, 2024 10:20 am
- Forum: General Woodworking
- Topic: Im happy I finally signed up
- Replies: 17
- Views: 590
Re: Im happy I finally signed up
I can think of at least 3 others in the last few months. No I don't have a photographic memory so don't ask for user names.
- Sun Feb 25, 2024 9:17 pm
- Forum: General Woodworking
- Topic: Im happy I finally signed up
- Replies: 17
- Views: 590
Re: Im happy I finally signed up
An unrelated link added at some point. We have seen more than one first poster with exactly the same subject and very close to the same text in the post. Probably a BOT. These need to be watched for SPAM.
Do you really think this is a legitimate first post???
Do you really think this is a legitimate first post???
- Sun Feb 25, 2024 12:26 pm
- Forum: General Woodworking
- Topic: Im happy I finally signed up
- Replies: 17
- Views: 590
Re: Im happy I finally signed up
Hmmm...
- Sat Feb 24, 2024 10:33 pm
- Forum: Maintenance and Repair
- Topic: Mark VII Idler Shaft Damage
- Replies: 42
- Views: 1634
Re: Mark VII Idler Shaft Damage
Before you pull your hair out, check with Motion Industries. If nothing else take the bearing in to them so they can measure it and come up with an equivalent. Many (most) bearings are speced in metric even in the US.
- Sat Feb 24, 2024 10:22 pm
- Forum: Maintenance and Repair
- Topic: Festool TS 55 won't start
- Replies: 9
- Views: 338
Re: Festool TS 55 won't start
I assume you checked the continuity of the power cord. The next thing I would check is the switch if you can get to it. Haven't checked either. Don't have a continuity tester. Without an Ohm meter I don't know how you would determine what is wrong. A cheap Volt/Ohm meter is under $10 most places.
- Sat Feb 24, 2024 8:43 pm
- Forum: Maintenance and Repair
- Topic: Festool TS 55 won't start
- Replies: 9
- Views: 338
Re: Festool TS 55 won't start
I assume you checked the continuity of the power cord. The next thing I would check is the switch if you can get to it.
- Sat Feb 24, 2024 12:21 pm
- Forum: Community
- Topic: Floating Glass Shelves
- Replies: 1
- Views: 255
Re: Floating Glass Shelves
You could us standard floating shelf brackets for wood shelves. Attach a strip of wood just large (thick/wide) enough to mount the bracket and put a groove in the front face to accommodate the glass and epoxy the glass in the groove.