Thanks Dusty!dusty wrote:
I have successfully installed three sets of casters using this template.
Search found 549 matches
- Wed Apr 18, 2018 1:55 pm
- Forum: Maintenance and Repair
- Topic: Premium casters, revision “D”
- Replies: 20
- Views: 16920
Re: Premium casters, revision “D”
- Wed Apr 18, 2018 6:16 am
- Forum: Maintenance and Repair
- Topic: Premium casters, revision “D”
- Replies: 20
- Views: 16920
Re: Premium casters, revision “D”
Ok Ed and Red, thx for the advice. I suppose both of you did not invert the SS to determine. And I further take it that 1-5/8” or a tad less might be the outcome. Now to find a decent 1/2” board to cut up for spacers before clamping.
- Tue Apr 17, 2018 8:29 pm
- Forum: Maintenance and Repair
- Topic: Premium casters, revision “D”
- Replies: 20
- Views: 16920
Premium casters, revision “D”
Just got the premium casters from SS, speedy delivery. I read through the entire LONG thread on these things, but still came away confused. Is the concensus that the current instructions and drilling template are correct (my SS is a 510 from 1984)? As I measure the template, the offset between old a...
- Tue Apr 10, 2018 2:01 am
- Forum: Maintenance and Repair
- Topic: Dust Collector motor
- Replies: 9
- Views: 12448
Re: Dust Collector motor
I have the same vac, and a year ago mine had the same problem. I took the motor cover off and found the failure point was at the switch. Poor contact, high resistance due to sparking and pitting. Easy fix.
- Mon Apr 09, 2018 8:42 pm
- Forum: Community
- Topic: Online ordering broken and not secure
- Replies: 14
- Views: 11638
Re: Online ordering broken and not secure
Just now tried to check out and the same info pops up.
- Sun Apr 08, 2018 2:08 am
- Forum: Community
- Topic: Spring Sale
- Replies: 34
- Views: 24836
Re: Spring Sale
Got a link for this Spring Sale?
- Wed Feb 28, 2018 2:32 pm
- Forum: General Woodworking
- Topic: Drill Press Using 2+ in Forstner bits
- Replies: 22
- Views: 27967
Re: Drill Press Using 2+ in Forstner bits
The slower the better. I guess your powerpro will slow down to 250 ish. I’ve read complaints about new Forstner bits being dull out of the box, there are articles online for how to sharpen “better than new”.
- Wed Feb 28, 2018 2:20 pm
- Forum: General Woodworking
- Topic: Drill Press Using 2+ in Forstner bits
- Replies: 22
- Views: 27967
Re: Drill Press Using 2+ in Forstner bits
Your rpms are ok for softwood, but perhaps too high for hardwood, per this article.
https://www.woodcraft.com/blog_entries/ ... n-use-care
My solution was to purchase a SS speed reducer, but I wanted it to turn large heavy blanks on the lathe, as well as large drill bits.
https://www.woodcraft.com/blog_entries/ ... n-use-care
My solution was to purchase a SS speed reducer, but I wanted it to turn large heavy blanks on the lathe, as well as large drill bits.
- Thu Jan 25, 2018 12:43 am
- Forum: Woodworking Tool Review
- Topic: W E N tools
- Replies: 7
- Views: 16650
Re: W E N tools
Shopsmith sold a small electric sharpener, made by Wen.
- Wed Jan 24, 2018 7:41 pm
- Forum: Community
- Topic: greenie jointer extension table
- Replies: 5
- Views: 5509