Search found 93 matches
- Wed Feb 28, 2018 2:00 pm
- Forum: General Woodworking
- Topic: Drill Press Using 2+ in Forstner bits
- Replies: 22
- Views: 27983
Re: Drill Press Using 2+ in Forstner bits
I have a PP--so a lower RPM than 650?
- Wed Feb 28, 2018 1:31 pm
- Forum: General Woodworking
- Topic: Drill Press Using 2+ in Forstner bits
- Replies: 22
- Views: 27983
Drill Press Using 2+ in Forstner bits
I am drilling large circles (holes) with a new 2 1/2" in Forstner bit. Depth of cut is 1/4". SS running at 650 RPM's. I find I am getting belt slip even though I have tighten the best has much as I am comfortable with. Any suggestions on how best to proceed?
- Sun Aug 27, 2017 3:25 pm
- Forum: Maintenance and Repair
- Topic: Speed Sensor for Power Pro-Replacement Instructions
- Replies: 5
- Views: 7481
Re: Speed Sensor for Power Pro-Replacement Instructions
Yes--agreed. Everything I did was in consultation with SS Tech Service
- Fri Aug 25, 2017 7:29 pm
- Forum: Maintenance and Repair
- Topic: How to Resolve a RPS State Error 0
- Replies: 51
- Views: 95000
Re: How to Resolve a RPS State Error 0
I just replaced the speed sensor and power supply. Everything works as of right now. I also posted instructions w pictures for replacing speed sensor since I could not find them anywhere, SS service was a big help with this. http://www.shopsmith.com/ss_forum/maintenance-and-repair-f10/speed-sensor-f...
- Fri Aug 25, 2017 2:08 pm
- Forum: Maintenance and Repair
- Topic: Speed Sensor for Power Pro-Replacement Instructions
- Replies: 5
- Views: 7481
Re: Speed Sensor for Power Pro-Replacement Instructions
Here is a PDF document with pictures
- Fri Aug 25, 2017 2:06 pm
- Forum: Maintenance and Repair
- Topic: Speed Sensor for Power Pro-Replacement Instructions
- Replies: 5
- Views: 7481
Speed Sensor for Power Pro-Replacement Instructions
I have been battling a RPS error for a month or tow (see string below. Did a DIY PP upgrade in 2014-worked great until earlier this year. Have replaced the power supply-worked for 3-5 days RPS error returned. Working w SS support, now replaced speed sensor and another new power supply (pending) http...
- Fri Aug 18, 2017 3:58 pm
- Forum: Maintenance and Repair
- Topic: How to Resolve a RPS State Error 0
- Replies: 51
- Views: 95000
Re: How to Resolve a RPS State Error 0
No not yet--SS is slated to send me a new power supply and speed sensor
- Wed Aug 09, 2017 10:17 am
- Forum: Maintenance and Repair
- Topic: How to Resolve a RPS State Error 0
- Replies: 51
- Views: 95000
Re: How to Resolve a RPS State Error 0
Well my RPS error message has returned. After successfully running the SS for 3-4 days, I started a turning project and the RPS error code pops up. When I push the ON button, the display shows run, then LOW, then RPS error, all in less then 2 seconds. Appreciate any guidance from the forum....
- Sun Jul 30, 2017 11:06 am
- Forum: Maintenance and Repair
- Topic: How to Resolve a RPS State Error 0
- Replies: 51
- Views: 95000
Re: How to Resolve a RPS State Error 0
First a BIG thank you to Charles. I did reassemble the entire headstock as Charles suggested and the system works-no errors. My bad, but a lesson well learned. I had no idea there were IR speed sensors that were integral to the PP system. At least I got much more proficient and comfortable at taking...
- Wed Jul 26, 2017 2:52 pm
- Forum: Maintenance and Repair
- Topic: How to Resolve a RPS State Error 0
- Replies: 51
- Views: 95000
Re: How to Resolve a RPS State Error 0
This is all I got--verbatim (cut and paste). I am looking at Wiki now.