stuck mitre gauge!
Moderators: HopefulSSer, admin
Re: stuck mitre gauge!
You could just buy another miter gauge. They are on eBay all the time. Still, part of the fun is in the fixing. I wouldn't give up quite yet.
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
- JPG
- Platinum Member
- Posts: 34610
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: stuck mitre gauge!
That is a 1/8" National Pipe Thread 'screw'. It is tapered both on the 'screw' and the miter gauge.
When wear makes it 'necessary' to advance the 'screw' until the screw refuses to advance, a strip of paper slipped under the bar and extending up both sides provides clamping without gorilla tactics.
When wear makes it 'necessary' to advance the 'screw' until the screw refuses to advance, a strip of paper slipped under the bar and extending up both sides provides clamping without gorilla tactics.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: stuck mitre gauge!
Try using a couple of flat head screw drivers in the slot on either side of the screw to force the sides of the bar to open more and maybe the screw will loosen up.
Ed from Rhode Island
510 PowerPro Double Tilt:Greenie PowerPro Drill Press:500 Sanding Shorty w/Belt&Strip Sanders
Super Sawsmith 2000:Scroll Saw w/Stand:Joint-Matic:Power Station:Power Stand:Bandsaw:Joiner:Jigsaw
1961 Goldie:1960 Sawsmith RAS:10ER
510 PowerPro Double Tilt:Greenie PowerPro Drill Press:500 Sanding Shorty w/Belt&Strip Sanders
Super Sawsmith 2000:Scroll Saw w/Stand:Joint-Matic:Power Station:Power Stand:Bandsaw:Joiner:Jigsaw
1961 Goldie:1960 Sawsmith RAS:10ER
- BuckeyeDennis
- Platinum Member
- Posts: 3683
- Joined: Tue Jul 24, 2012 10:03 pm
- Location: Central Ohio
Re: stuck mitre gauge!
You should be able to get the screw out of the miter bar by relieving the pressure on it. See if you can insert a steel wedge (screwdriver, junk plane iron or chisel, etc.) into the slot into the miter bar, and tap it in until the miter bar spreads a bit more. Then the tapered screw should come out easily. Shopsmith sells replacement screws -- I bought a new one to replace an old balky one a couple of years ago.
Re: stuck mitre gauge!
The idea to use a screwdriver as a wedge worked! Thanks everyone! Now I only need to purchase a new screw which isn't too difficult (though it may be awhile before SS sends it to me).
Thanks for everyone's help!
Thanks for everyone's help!
"Like a bull chasing the matador is the man left to his own schemes
Everybody needs someone beside em' shining like a lighthouse from the sea" - Brother, NEEDTOBREATHE
Everybody needs someone beside em' shining like a lighthouse from the sea" - Brother, NEEDTOBREATHE