Shorter Arbor

Forum for people who are new to woodworking. Feel free to ask questions or contribute.

Moderators: HopefulSSer, admin

User avatar
chapmanruss
Platinum Member
Posts: 3448
Joined: Tue Aug 26, 2014 8:16 pm
Location: near Portland, Oregon

Re: Shorter Arbor

Post by chapmanruss »

Mike,

You said in your post above
I also found and bought a shaper/sander fence which should be here Friday.
I hope you found the Shaper Fence for the Mark VII. There have been three different fences made over the years. The first is for the Mark 5 with the original table system aka Mark V 500 and will fit the Shopsmith Model 10's also. The second is specifically for the 1960's Mark VII and is show in the picture below. It has been out of production for a very long time. The third is for the Mark V 510, 505, 520 and Mark 7 all with the larger table system.

_
Mark VII Shaper Fence.jpg
Mark VII Shaper Fence.jpg (67.67 KiB) Viewed 2609 times
_
Note the attachment bolts are in between the fence adjustment knobs and go through holes in the table.

Stay with the lower blade guard you have currently. The original one made for the Mark VII is a cast aluminum guard that wraps around both sides of the blade and is not extendable. It is in the picture below.

_
505705 Saw Dust Chute.jpg
505705 Saw Dust Chute.jpg (50.84 KiB) Viewed 2609 times
_
As JPG said
Unfortunately Mark VII and Mark 7 do get interchanged occasionally
To add to the confusion the Mark VII from the 1960's has both Mark VII and Mark 7 on it. Generally speaking Mark VII is referred to the 1960's model and Mark 7 is the current model. For clarification I like to use 1960's Mark VII or current Mark 7 although I sometimes neglect to.
Russ

Mark V completely upgraded to Mark 7
Mark V 520
All SPT's & 2 Power Stations
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored. Others to be restored.
br549
Platinum Member
Posts: 623
Joined: Sun Nov 30, 2014 8:51 am
Location: Midway between Houston/Galveston, TX

Re: Shorter Arbor

Post by br549 »

miken,

You are correct about the 5/8" arbor part number for a Mark 5/V/500 ... it is 555321. Sorry for adding to the confusion.

And yes, there are new arbors on ebay from a third party supplier that cost more than from Shopsmith. Unless you are in a big rush and Shopsmith is out of stock, I don't understand either why someone why pay more. Used 555321 arbors do occasionally come up for sale on ebay at a slightly lower price. I got mine a few years ago that way for about half the cost of new from Shopsmith.

I am not very familiar with Mark VIIs from the 1960's, but based on my experience with my Mark V (500), the difference in length between a 555321 and a 555608 is about 5 mm. I know this because I mistakenly purchased a 555608 arbor before I understood the differences. The 555608 worked and I used it for several years before getting the 555321. I simply had to use the quill extension to get the blade to be more or less centered in the saw table insert. I don't recall, but I was probably using it with a spacer in my lower guard. Whether the previous version of a 5/8" arbor for the 505/510/520/Mark 7 (P/N 555118) is also 5 mm longer, I don't know. And whether or not the 555608 or the 555118 are even an option for your Mark VII and your lower guard, I don't know.

(NOTE: My overall length measurements are approximate, with a gap left for approximately a 1/8" thick blade on both arbors.)
Attachments
555608 left, 555321 right
555608 left, 555321 right
PA072597resized.jpg (51.37 KiB) Viewed 2601 times
555608 length 57mm
555608 length 57mm
PA072605resized.jpg (52.14 KiB) Viewed 2601 times
555321 length 52 mm
555321 length 52 mm
PA072607resized.jpg (45.8 KiB) Viewed 2601 times
User avatar
miken
Gold Member
Posts: 239
Joined: Sat Nov 14, 2020 10:28 pm
Location: Maine

Re: Shorter Arbor

Post by miken »

chapmanruss wrote: Tue May 04, 2021 12:16 am I hope you found the Shaper Fence for the Mark VII. There have been three different fences made over the years.
This is a picture of the one I bought. I had holes already drilled in my table. I measured the distance between them at 3 3/8" center to center and had the seller confirm the same spacing. I am pretty sure it is correct, and looks like your picture. It was an impulse buy. I already have a separate craftsman router and table. ;)

Thanks for the info, really appreciate it.
Mike -
Attachments
5.JPG
5.JPG (40.45 KiB) Viewed 2600 times
ShopSmith Mark VII (406982), with Band Saw, Jig Saw, Belt Sander, and Jointer
ShopSmith Mark VII (400457), (working backup or parts machine)
12" Craftsman Band Saw (113.243311)
12" Craftsman Powered Hacksaw (108.1501)
12" Atlas Commercial (3990) 12" Back Geared, Undermount, Screw Cutting Lathe with Quick Change Gear Box, Taper, Milling and Grinding Attachments
Atlas MFC Horizontal Milling Machine with Vertical Milling Attachment
Atlas 7B Metal Shaper
User avatar
miken
Gold Member
Posts: 239
Joined: Sat Nov 14, 2020 10:28 pm
Location: Maine

Re: Shorter Arbor

Post by miken »

br549 wrote: Tue May 04, 2021 7:08 am You are correct about the 5/8" arbor part number for a Mark 5/V/500 ... it is 555321. Sorry for adding to the confusion.
No worries at all. I knew what you meant and really appreciate the help.
br549 wrote: Tue May 04, 2021 7:08 am And yes, there are new arbors on ebay from a third party supplier that cost more than from Shopsmith. Unless you are in a big rush and Shopsmith is out of stock, I don't understand either why someone why pay more.
A lot of the Shopsmith stuff on eBay is ridiculously priced, but they know supplies are limited.

br549 wrote: Tue May 04, 2021 7:08 am I don't recall, but I was probably using it with a spacer in my lower guard.
I was mostly concerned with the order of the arbor spacers. I have always used it with the thickest spacer first, then the blade, then the thinner spacer, lock tab washer, nut. To get the blade to align with the riving knife I have to put the thin spacer on first.
I think the 555321 is my best choice, and I haven't found one on eBay for cheap, so I may just buy from Shopsmith.

Thanks for the arbor pics and dimensions.
Mike -
ShopSmith Mark VII (406982), with Band Saw, Jig Saw, Belt Sander, and Jointer
ShopSmith Mark VII (400457), (working backup or parts machine)
12" Craftsman Band Saw (113.243311)
12" Craftsman Powered Hacksaw (108.1501)
12" Atlas Commercial (3990) 12" Back Geared, Undermount, Screw Cutting Lathe with Quick Change Gear Box, Taper, Milling and Grinding Attachments
Atlas MFC Horizontal Milling Machine with Vertical Milling Attachment
Atlas 7B Metal Shaper
User avatar
chapmanruss
Platinum Member
Posts: 3448
Joined: Tue Aug 26, 2014 8:16 pm
Location: near Portland, Oregon

Re: Shorter Arbor

Post by chapmanruss »

Mike,

I an glad to see you found the correct Shaper Fence.

If you checked out the link br549 provided in a previous post you should have found two PDF's in my post. Scroll up from where the link takes you to that post. One has a picture of many of the Arbors from over the years and the other is a listing of the Arbors with additional information. The pictures below are more complete than the one in the PDF. Use these pictures as a reference to the PDF with the listing of the Arbors. These pictures do not include the Shaper Spindles, Router Chucks or SawSmith Arbors.

_
Arbors page 1 - labeled.jpg
Arbors page 1 - labeled.jpg (150.85 KiB) Viewed 2584 times
There was an error in the labeling of 12 031 and 22 031 in previous postings of the above picture. Anyone having saved it should replace it with this one.
_
Arbors page 2 - labeled.jpg
Arbors page 2 - labeled.jpg (108.45 KiB) Viewed 2584 times
_
The picture below shows the Lower Blade Guard you are using on my Model 10ER. Notice I have the saw blade on an earlier version of the 5/8" Arbor with a machined washer first followed by the blade and than the machined spacer. My Lower Blade Guard does not have the aluminum spacer in this instance. That Arbor P/N 12 031 has a shorter, by 1/8", base length than the 5/8" Universal or Molder/Dado Arbor P/N 505506 you are using. With the spacing of the quill/spindle differences of the Model 10ER and the Mark VII you may still need the spacer in the Lower Blade Guard if using the 5/8" Universal Arbor for saw blades. All that being said you could still get a 5/8" Saw Blade Arbor P/N 555321 for use on your Mark VII. It may still need to have the spacer in the lower guard depending on where the blade is positioned in the guard by the arbor. The 1-1/4" Arbor P/N 505511 puts the blade 1-1/4" out from the base end of the arbor. The 5/8" Arbor P/N 555321 puts the blade 1-1/2" out from the base end of the arbor. The 5/8" Universal Arbor P/N 505506 puts the blade 1-11/16" out from the base end of the arbor with the machined washer first. All three of these arbors, which are for use on the Mark 5 aka Mark V 500, will put the blade at different positions relative to the quill end.

_
505628 on 10ER.jpg
505628 on 10ER.jpg (103.15 KiB) Viewed 2584 times
_
Mike, I will tell you I have never owned a 1960's Mark VII so I can only go on what I have learned about them. Others who own them can give more specific information about their differences compared to a Mark 5. I do know a lot about Shopsmith Arbors.

I hope we haven't overloaded you with too much information.
Russ

Mark V completely upgraded to Mark 7
Mark V 520
All SPT's & 2 Power Stations
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored. Others to be restored.
User avatar
miken
Gold Member
Posts: 239
Joined: Sat Nov 14, 2020 10:28 pm
Location: Maine

Re: Shorter Arbor

Post by miken »

chapmanruss wrote: Tue May 04, 2021 1:07 pm If you checked out the link br549 provided in a previous post you should have found two PDF's in my post.
Yes, I have those pdf's, but will reference the pictures in this thread in the future.
chapmanruss wrote: Tue May 04, 2021 1:07 pm With the spacing of the quill/spindle differences of the Model 10ER and the Mark VII you may still need the spacer in the Lower Blade Guard if using the 5/8" Universal Arbor for saw blades.
Yes I do need the guard spacer. The arbor looks like it sits back further on the 10ER than the VII. See my picture below as compared to yours above.
chapmanruss wrote: Tue May 04, 2021 1:07 pm The 5/8" Arbor P/N 555321 puts the blade 1-1/2" out from the base end of the arbor.
Yes, I know the picture below doesn't show it well, but 1 1/2" basically will put my blade where the first washer (arbor spacer) is now. If it does fit in the guard, it would be uncomfortably close. I may just stick with what I have. I don't see a real benefit to switching to the 555321 after all.
chapmanruss wrote: Tue May 04, 2021 1:07 pm I hope we haven't overloaded you with too much information.
Nope. I am catching on slowly, and I keep coming back to my posts to review.
Thanks again, Mike -
Attachments
6.jpg
6.jpg (35.24 KiB) Viewed 2568 times
ShopSmith Mark VII (406982), with Band Saw, Jig Saw, Belt Sander, and Jointer
ShopSmith Mark VII (400457), (working backup or parts machine)
12" Craftsman Band Saw (113.243311)
12" Craftsman Powered Hacksaw (108.1501)
12" Atlas Commercial (3990) 12" Back Geared, Undermount, Screw Cutting Lathe with Quick Change Gear Box, Taper, Milling and Grinding Attachments
Atlas MFC Horizontal Milling Machine with Vertical Milling Attachment
Atlas 7B Metal Shaper
User avatar
chapmanruss
Platinum Member
Posts: 3448
Joined: Tue Aug 26, 2014 8:16 pm
Location: near Portland, Oregon

Re: Shorter Arbor

Post by chapmanruss »

Sorry I didn't have a picture of the Lower Blade Guard on a Mark to show its spacing. Having it on my Model 10ER is like comparing apples to oranges. The Quill Assemblies are different between the Model 10's and the Mark 5 and Mark VII which both have the spindle knob. That's the part under the 2 of the tape measure in your picture above. It adds additional distance between the mounting collar of the guard and where the blade ends up on the Mark series tools.
Russ

Mark V completely upgraded to Mark 7
Mark V 520
All SPT's & 2 Power Stations
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored. Others to be restored.
User avatar
miken
Gold Member
Posts: 239
Joined: Sat Nov 14, 2020 10:28 pm
Location: Maine

Re: Shorter Arbor

Post by miken »

chapmanruss wrote: Wed May 05, 2021 12:27 pm Sorry I didn't have a picture of the Lower Blade Guard on a Mark to show its spacing. Having it on my Model 10ER is like comparing apples to oranges.
No problem at all. I learned what I needed to know, and appreciate your help.
Funny coincidence, you are located near Portland Oregon, and I am located near Portland Maine. :)
ShopSmith Mark VII (406982), with Band Saw, Jig Saw, Belt Sander, and Jointer
ShopSmith Mark VII (400457), (working backup or parts machine)
12" Craftsman Band Saw (113.243311)
12" Craftsman Powered Hacksaw (108.1501)
12" Atlas Commercial (3990) 12" Back Geared, Undermount, Screw Cutting Lathe with Quick Change Gear Box, Taper, Milling and Grinding Attachments
Atlas MFC Horizontal Milling Machine with Vertical Milling Attachment
Atlas 7B Metal Shaper
User avatar
chapmanruss
Platinum Member
Posts: 3448
Joined: Tue Aug 26, 2014 8:16 pm
Location: near Portland, Oregon

Re: Shorter Arbor

Post by chapmanruss »

Portland Oregon is named after Portland Maine. It was decided by a coin toss and if the coin had landed the other side up I would be leaving near Boston Oregon.
Russ

Mark V completely upgraded to Mark 7
Mark V 520
All SPT's & 2 Power Stations
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored. Others to be restored.
StevenAyres
Gold Member
Posts: 84
Joined: Sun Apr 21, 2019 11:21 am
Location: Prescott AZ

Re: Shorter Arbor

Post by StevenAyres »

An idea that hasn't yet been explored in this thread is blade choice for the Mark VII. To use the original system (aluminum guard as pictured below, carriage lock aligning the blade to the table slots), you'll definitely prefer to use the original short arbors and 9" blades by Magna. Those blades come available frequently on Ebay and such for not much money, they're of high quality for their time and sharpen up well. I haven't seen any carbides, but having the standard blades sharpened is inexpensive too.

The second photo is of the same setup (also 9" blade) using a 3D-printed guard I recently purchased through the Facebook Shopsmith User Group. It will take the 12" sanding discs, whether cast aluminum, flat steel or conical, and uses a set of bolt-in spacers to provide for whatever arbor you need. This allows me to use the 10" Magna blades (including carbides) in the Mark VII system. If you like another blade, your sharpening service can probably bore it out for the short arbor.
Attachments
Mark VII blade setup.jpg
Mark VII blade setup.jpg (33.35 KiB) Viewed 2435 times
Mark VII with all-purpose guard.jpg
Mark VII with all-purpose guard.jpg (28.73 KiB) Viewed 2434 times
Last edited by StevenAyres on Sat May 08, 2021 7:36 pm, edited 1 time in total.
Post Reply