Utility Table With Casters

Forum for people who are new to woodworking. Feel free to ask questions or contribute.

Moderators: HopefulSSer, admin

Post Reply
User avatar
SteveMaryland
Gold Member
Posts: 187
Joined: Sat Nov 06, 2021 3:41 pm
Location: Baltimore, Maryland

Utility Table With Casters

Post by SteveMaryland »

I previously used ordinary folding-leg tables but they proved to be inadequate for heavy work.

I wanted a folding-leg table that had a dead flat top, strong legs, and removable casters on the table-edge so I could roll the table instead of dragging it.

The result is the table shown. I built two. Top is just a 4x8 3/4" plywood sawn to 2x8. Sides are 2x4's thru-bolted to the top. On the 2x4's I bolted 1/4" thk long steel plates, these are what keep the top flat and straight. Casters are demountable, they plug into blocks mounted on the table edges. One problem with these blocks is - don't make them from wood. Use steel. Wood breaks under the stress.

Tables are heavy but no problem because they roll to wherever they are needed. T-nuts, socket head screws and locknuts used throughout. Thru holes only, no tapped holes in wood.

Table legs - Tent and Table SKU AX-BT3096LG. This buys 1 pair of legs.

Casters - SurplusCenter.com, P/N 1-3366. Two casters per table. The stem on these has no threads - they plug into a hole on the table. I think the wheel dia is 4". Don't buy threaded stems unless you are ready to use a wrench every time you want to remove the casters. Don't buy tiny wheels, buy a 4" dia minimum.

The steel plates underneath were from Home Depot.

For the "beginning" woodworker, this would be an ideal first project. Just need a Shopsmith - and a table...
Attachments
UTILITY TABLE WITH CASTERS.pdf
(1.84 MiB) Downloaded 476 times
Mark V, Model 555510, Serial No. 102689, purchased November 1989. Upgraded to 520
Hobbyman2
Platinum Member
Posts: 2660
Joined: Wed Feb 01, 2017 12:52 am
Location: Ohio

Re: Utility Table With Casters

Post by Hobbyman2 »

just a tip when posting pictures , I create a folder on my computer desk top and send a copy of the photo to it then up load it to the forum from the desk top folder . I have a lot of folders showing up in your attachment . jmo
Hobbyman2 Favorite Quote: "If a man does his best, what else is there?"
- General George S. Patton (1885-1945)
tom85
Bronze Member
Posts: 5
Joined: Thu Feb 11, 2021 5:17 am

Re: Utility Table With Casters

Post by tom85 »

SteveMaryland wrote: Sat Nov 13, 2021 12:30 pm I previously used ordinary folding-leg tables but they proved to be inadequate for heavy work.

I wanted a folding-leg table that had a dead flat top, strong legs, and removable casters on the table-edge so I could roll the table instead of dragging it.

The result is the table shown. I built two. Top is just a 4x8 3/4" plywood sawn to 2x8. Sides are 2x4's thru-bolted to the top. On the 2x4's I bolted 1/4" thk long steel plates, these are what keep the top flat and straight. Casters are demountable, they plug into blocks mounted on the table edges. One problem with these blocks is - don't make them from wood. Use steel. Wood breaks under the stress.

Tables are heavy but no problem because they roll to wherever they are needed. T-nuts, socket head screws and locknuts used throughout. Thru holes only, no tapped holes in wood.

Table legs - Tent and Table SKU AX-BT3096LG. This buys 1 pair of legs.

Casters - SurplusCenter.com, P/N 1-3366. Two casters per table. The stem on these has no threads - they plug into a hole on the table. I think the wheel dia is 4". Don't buy threaded stems unless you are ready to use a wrench every time you want to remove the casters. Don't buy tiny wheels, buy a 4" dia minimum.

The steel plates underneath were from Home Depot.
Las Atlantis casino https://las-atlantiscasino.com/ is the best casino for everyone who is interested in online gambling, all my friends play there and make good money.
For the "beginning" woodworker, this would be an ideal first project. Just need a Shopsmith - and a table...
Looks nice! Thanks for pdf!
Last edited by tom85 on Fri Nov 26, 2021 10:21 am, edited 1 time in total.
User avatar
rpd
Platinum Member
Posts: 3039
Joined: Tue Apr 05, 2011 3:22 am
Location: Victoria, B.C.

Re: Utility Table With Casters

Post by rpd »

photos in the pdf
table1.jpg
table1.jpg (473.89 KiB) Viewed 7003 times
table2.jpg
table2.jpg (470.56 KiB) Viewed 7003 times
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
User avatar
SteveMaryland
Gold Member
Posts: 187
Joined: Sat Nov 06, 2021 3:41 pm
Location: Baltimore, Maryland

Re: Utility Table With Casters

Post by SteveMaryland »

I have improved my utility tables with two improvements.

1. Casters allow for table portability - table does not stand on the casters when in use. These casters are the "plug-in" type, not the bolt-on type. They have a 7/16" dia pin-stud instead of a threaded stud. This allows for easy caster removal. The bore that they plug into has to be very strong - stronger than the oak blocks I used originally. Those blocks cracked, and I glued, and they cracked again. I wanted to replace them with steel, but I am not setup for heavy steel work, and I did not want to go to a machine shop. So I had a metal sales shop (Metals Supermarkets) cut me some blank aluminum blocks, which I bored out (I can at least bore aluminum). Then I got hardened steel "drill bushings" from McMaster Carr, and pressed these into the blocks. Also I thru-bolted the blocks onto the table instead of just wood screws. So now I have really strong caster mounting blocks that will never break at the wrong time and mess up my work schedule.

2. Each folding leg mechanism presents a pair of legs, and these legs are strong but I wanted something with more ground bearing that would allow me to drag a table across rough surfaces without leg damage. So now each leg pair is joined by a single wood stretcher. Tables are now much more stable and durable than before.

These metal sales shops (Online metals, Metals Supermarkets etc) are a good resource. As is McMaster Carr. They do the heavy cutting, and thus allow us to incorporate more metal into our projects than we otherwise would.

These tables have become indispensable in my Shopsmith work. I highly recommend this table design as a build project for a new or old woodworker or anyone else who needs a large, strong yet portable work platform.

Come to think of it, a decent general purpose portable platform might be a good new Shopsmith product - or at least the hardware kit to make one.
Attachments
c3.JPG
c3.JPG (136.36 KiB) Viewed 4823 times
c2.JPG
c2.JPG (97.81 KiB) Viewed 4823 times
c1.JPG
c1.JPG (80.27 KiB) Viewed 4823 times
c4.JPG
c4.JPG (101.62 KiB) Viewed 4823 times
Mark V, Model 555510, Serial No. 102689, purchased November 1989. Upgraded to 520
User avatar
JPG
Platinum Member
Posts: 34610
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Re: Utility Table With Casters

Post by JPG »

Note all that the casters are mounted on the horizontal rails of the table frame just below the top.

Took me a while to understand that.
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10
E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Post Reply