I also modeled and 3D printed the upper and lower soft jaws.
Then I went down a rabbit hole of looking at all sorts of Zyliss variations. Some have the quick release as mentioned in this thread. Some have horizontal slots on the jaw bases, and some have a lower slot for mounting to an optional pivot plate. The table clamps had at least three minor variations. Various sources claim the vise was developed sometime in the 50s or 60s as a portable tool for the Swiss Army. It was later mass marketed as a hobbyist vise.
And that is only is the Zyliss branded version. There are/were countless clones and/or licensees with various extra parts or features. So far I've found Grip Master, Vunder Vise, Z-Vise, Z-Vise 2, OZ Vice, Extra Pair of Hands VIce, and SwissRex. SwissRex later produced a functionally similar, but different looking version.
I have an original Zyliss Vice. It was gifted to me two years back in the original box with the instructions, plus a quick review card for on the fly mounting. Here is what I know...
Mine was bought in 1979. They were really big at county fairs and that sort of thing. I have the original receipt for $289.00. That was in 1979.... Fast Forward! The distribution guy now lives in New Zealand. The ones being sold now are not nearly as strong/good as the originals that were Swiss made. Back in the day the Zyliss Vice was King. I read an article several years back where a motorcyclist had one and convinced his buddy to buy one. They busted the new one right out of the box. From what he said they were really cranking on the new one. These dudes did a side by side comparison and found multiple differences in the castings. They had cut Manufacturing details that made them prone to breakage. The new Zyliss Vices are sold in a blown molded plastic case. The newer models also came with additional accessories so the vice could be set up as a drill press among other things. Since the jaws are made of aluminum one needs to be mindful so you don’t damage the face of the jaws. Mine has a set of plastic jaw covers the I always use. The new model comes with a set of plastic jaw covers as well as sheet metal jaw covers that snap on. I fabricated 3 sets of metal jaw covers for now and future needs. I tried to buy just the new case from the dude in New Zealand. With shipping it was insanely priced. I ended up storing mine in an older Hip Roof Craftsman tool box. It fits perfectly. The originals are excellent tools. The crank arm on the vice is most excellent. How can you know the difference? I do not know. Other than the one I own I have never seen another one. They are VERY expensive but worth every penny (so I am told). I don’t know how to post up a photo or two. SORRY!
SS Model 5 500 Completely Restored
SS Bandsaw Completely Restored
SS Jointer Completly Restored
SS Biscuit Cutter
Rikon Low Speed Grinder W/Wolverine jig
Kreg Tool TrackHorse X 2 + Kreg Tool Project Center with 35 Kreg Tool Clamps
11 Systematic Blades of every configuration
Bosch/Mikita handheld power tools plus every hand tool in the book.
Ulmia Chisel sets X 3
Permobile Custom RideForward Powerchair
Complete set of registered # NASA X-15 Custom Tools W/Ownership certificate
1998 510 upgraded to a 520, upgraded to power pro with double tilt and lift assist.
overarm pin router
Lots of minor differences such as the design of the handle arm, lack of quick-release, and lack of notches in the base for mounting accessories such as "lower soft jaws". There are also spring pins holding the way bars to the right jaw.
The table clamps have a smaller mouth and the springs are much weaker. Once I got past the dirt, paint, and corrosion I found the overall original finish was not as refined as my later model. I smoothed some of that with progressive grits before polishing.
When this arrived nothing moved. It took me hours just to get it to move, and a few more to disassemble.
- Platinum Member
- Posts: 31974
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (WILDCAT territory)
Starting a museum?
Yes how did you get that shiney finish.
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange