Two Tools to use for Table to Blade Alignment

Create a review for a woodworking tool that you are familiar with (Shopsmith brand or Non-Shopsmith) or just post your opinion on a specific tool. Head to head comparisons welcome too.

Moderators: HopefulSSer, admin

Post Reply
User avatar
dusty
Platinum Member
Posts: 21359
Joined: Wed Nov 22, 2006 6:52 am
Location: Tucson (Wildcat Country), Arizona

Two Tools to use for Table to Blade Alignment

Post by dusty »

There have been recent discussion about instrumentation that can be used to perform "Shopsmith Table to Blade Alignment".

The two Tools are the MAG-DRO and the SuperBar. I have both. Of the two I much prefer the SuperBar. The photo shots that I am presenting here clearly show either can be used to gather reliable data for their intended purpose.

This is not intended as a component review simply because there are too many factors that go into evaluating the whole tool that I have not documented.

I hope the photos speak fro them selves

MAG-DRO:
20210421_093443.jpg
20210421_093443.jpg (464.26 KiB) Viewed 1997 times
20210421_093514.jpg
20210421_093514.jpg (473.43 KiB) Viewed 1997 times
20210421_093540.jpg
20210421_093540.jpg (473.27 KiB) Viewed 1997 times
20210421_093619.jpg
20210421_093619.jpg (418.95 KiB) Viewed 1997 times
SuperBar:
20210421_093731.jpg
20210421_093731.jpg (355.88 KiB) Viewed 1997 times
20210421_093747.jpg
20210421_093747.jpg (331.47 KiB) Viewed 1997 times
20210421_093803.jpg
20210421_093803.jpg (401.02 KiB) Viewed 1997 times
Attachments
20210421_093820.jpg
20210421_093820.jpg (431.34 KiB) Viewed 1997 times
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
bainin
Platinum Member
Posts: 542
Joined: Mon Apr 22, 2019 11:09 pm
Location: NC

Re: Two Tools to use for Table to Blade Alignment

Post by bainin »

Hey Dusty - your image of the dial gauge reminded me of thought i had when doing a setup.

It looks like the dial gauge is making an angle (possibly in 2 directions) to what would be the surface normal (the plate) . I had something similar due to something being in the way or wanting to land on my saw blade at a certain point ..i forget what exactly.

For a true reading of displacement-that dial indicator would need to be perpendicular to the measured surface right ? but maybe a true reading isn't important so long as the displacement on the indicator is small . I think if I remember my trig, that the displacement in this configuration would be larger than the actual displacement by cosine of the included angle.

b
User avatar
dusty
Platinum Member
Posts: 21359
Joined: Wed Nov 22, 2006 6:52 am
Location: Tucson (Wildcat Country), Arizona

Re: Two Tools to use for Table to Blade Alignment

Post by dusty »

Something is not right in the pictures with the dial indicator. It should not be 0.000 in all three and that is what it looks like. The numbers with the MAG-DRO are near what I expected.

These images are real world. I cannot explain the three with no deflection at all.

20210421_113547.jpg
20210421_113547.jpg (253.23 KiB) Viewed 1970 times
20210421_113605.jpg
20210421_113605.jpg (261.9 KiB) Viewed 1970 times
20210421_113622.jpg
20210421_113622.jpg (288.69 KiB) Viewed 1970 times
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
RFGuy
Platinum Member
Posts: 2740
Joined: Mon Dec 31, 2018 8:05 am
Location: a suburb of PHX, AZ

Re: Two Tools to use for Table to Blade Alignment

Post by RFGuy »

One question...for the MAG DRO, how do you determine how hard to press on the caliper thumb wheel to get a measurement? At least with a dial indicator there is a consistent spring tension that follows whatever reference surface you are measuring. With the MAG DRO though you have to push on the thumb wheel of the caliper to register the caliper rod against the reference surface. I would expect it will be hard to use the same force every time to get consistent results using this. Also, when pushing on the thumbwheel can it introduce error through table, reference surface, MAG DRO, etc. flex from pushing on the caliper?
📶RF Guy

Mark V 520 (Bought New '98) | 4" jointer | 6" beltsander | 12" planer | bandsaw | router table | speed reducer | univ. tool rest
Porter Cable 12" Compound Miter Saw | Rikon 8" Low Speed Bench Grinder w/CBN wheels | Jessem Clear-Cut TS™ Stock Guides
Festool (Emerald): DF 500 Q | RO 150 FEQ | OF 1400 EQ | TS 55 REQ | CT 26 E
DC3300 | Shopvac w/ClearVue CV06 Mini Cyclone | JDS AirTech 2000 | Sundstrom PAPR | Dylos DC1100 Pro particulate monitor
User avatar
dusty
Platinum Member
Posts: 21359
Joined: Wed Nov 22, 2006 6:52 am
Location: Tucson (Wildcat Country), Arizona

Re: Two Tools to use for Table to Blade Alignment

Post by dusty »

Not applying force to that wheel greater than what is required to advance it is the trick to getting valid readings from the caliper. It is possible to introduce bad readings with too much force.

Being flat on the table as it is with the MAG-DRO, the caliper button is difficult to advance properly. I gently push on the body of the gage to move it. If a reading doesn't seem right - back off and do it again.

Can one introduce error - absolutely. Gentle, one-finger push and listen for contact.

The Infinity plate that I have rings when contacted by the caliper. There is a touch required. This is true in all applications using the caliper (dital or otherwise).
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
User avatar
dusty
Platinum Member
Posts: 21359
Joined: Wed Nov 22, 2006 6:52 am
Location: Tucson (Wildcat Country), Arizona

Re: Two Tools to use for Table to Blade Alignment

Post by dusty »

bainin wrote: Wed Apr 21, 2021 2:17 pm Hey Dusty - your image of the dial gauge reminded me of thought i had when doing a setup.

It looks like the dial gauge is making an angle (possibly in 2 directions) to what would be the surface normal (the plate) . I had something similar due to something being in the way or wanting to land on my saw blade at a certain point ..i forget what exactly.

For a true reading of displacement-that dial indicator would need to be perpendicular to the measured surface right ? but maybe a true reading isn't important so long as the displacement on the indicator is small . I think if I remember my trig, that the displacement in this configuration would be larger than the actual displacement by cosine of the included angle.

b
Absolutely. The proper way is for the plunger to meet the reference surface at 90° (if the number is to be an accurate measurement of separation). Being used for this purpose we are looking for a reading that is consistently the same each and every time, indicating parallelism. If the plunger is at an angle, it is actually measuring the hypotenuse of the right triangle formed by the setup.

At an angle, the tip of the plunger can also side at point of contact.

What you cannot see in the corrected set of pictures is that the plunger bar is closer to being parallel to the table top.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
User avatar
dusty
Platinum Member
Posts: 21359
Joined: Wed Nov 22, 2006 6:52 am
Location: Tucson (Wildcat Country), Arizona

Re: Three Tools to use for Table to Blade Alignment

Post by dusty »

I have resurrected my very first dial indicator used for Table to Blade alignment.

I brought back the Shopsmith version. I think a comparison of the three is going to be interesting - and maybe an eye opener for me.

The Shopsmith and the SuperBar:
The Shopsmith Dial Indicator Set-Up 555884
The Shopsmith Dial Indicator Set-Up 555884
20210421_151538.jpg (303.26 KiB) Viewed 1910 times
The SuperBar
The SuperBar
20210421_151602.jpg (299.26 KiB) Viewed 1910 times
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
User avatar
miken
Gold Member
Posts: 240
Joined: Sat Nov 14, 2020 10:28 pm
Location: Maine

Re: Three Tools to use for Table to Blade Alignment

Post by miken »

dusty wrote: Wed Apr 21, 2021 6:46 pm I brought back the Shopsmith version. I think a comparison of the three is going to be interesting - and maybe an eye opener for me.
I am looking forward to your results Dusty.

Question: do you rotate the infinity plate as you take a reading from the infeed side to the outfeed side? Or perhaps the infinity plate is certified flat and perpendicular to the shaft? I ask because I am only using my sanding disk and it is not flat, so I mark a dot on the edge and then rotate the disk to measure from the same exact point.

Thanks, Mike -
ShopSmith Mark VII (406982), with Band Saw, Jig Saw, Belt Sander, and Jointer
ShopSmith Mark VII (400457), (working backup or parts machine)
12" Craftsman Band Saw (113.243311)
12" Craftsman Powered Hacksaw (108.1501)
12" Atlas Commercial (3990) 12" Back Geared, Undermount, Screw Cutting Lathe with Quick Change Gear Box, Taper, Milling and Grinding Attachments
Atlas MFC Horizontal Milling Machine with Vertical Milling Attachment
Atlas 7B Metal Shaper
User avatar
dusty
Platinum Member
Posts: 21359
Joined: Wed Nov 22, 2006 6:52 am
Location: Tucson (Wildcat Country), Arizona

Re: Three Tools to use for Table to Blade Alignment

Post by dusty »

miken wrote: Thu Apr 22, 2021 12:22 pm
dusty wrote: Wed Apr 21, 2021 6:46 pm I brought back the Shopsmith version. I think a comparison of the three is going to be interesting - and maybe an eye opener for me.
I am looking forward to your results Dusty.

Question: do you rotate the infinity plate as you take a reading from the infeed side to the outfeed side? Or perhaps the infinity plate is certified flat and perpendicular to the shaft? I ask because I am only using my sanding disk and it is not flat, so I mark a dot on the edge and then rotate the disk to measure from the same exact point.

Thanks, Mike -
This really depends on how precise you want to be. Picking a spot for contact and rotating back and forth yields the most accurate alignment. The sanding disk should be treated like a blade to get reliable results. I use a disk from Infinity and I still mark a spot and rotate back and forth. No Shortcuts when doing alignments.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Post Reply