I was sorting some tools and stuff in the old shop today (yes, I am still moving) and was standing petting my Mark VII while planning its move. I was puttering with it and studying the fence when I noticed the miter gauge lock. In earlier discussions of the Mark VII I had forgotten the miter gauge lock. It has a cam lock instead of tightening a knob. The cam lock uses a "U" shaped lock that you can flip down with your thumbs assuming that you have worked carefully and have thumbs.
The fence of course also uses a cam lock. It has a rather long lever on it that "feels" good to me.
I am looking forward to getting it moved and lubed and putting it to work. Back when I bought it I had a lot of other stuff going on and had mostly just shoved it back in a corner since I didn't really need it and only used it a little.
.
--
farmer
Francis Robinson
I did not equip with Shopsmiths in spite of the setups but because of them.
1 1988 - Mark V 510 (bought new), 4 Poly vee 1 1/8th HP Mark V's, Mark VII, 1 Mark V Mini, 1 Frankensmith, 1 10-ER, 1 Mark V Push-me-Pull-me Drillpress, SS bandsaw, belt sander, jointer, jigsaw, shaper attach, mortising attach, TS-3650 Rigid tablesaw, RAS, 6" long bed jointer, Foley/Belsaw Planer/molder/ripsaw, 1" sander, oscillating spindle/belt sander, Scroll saw, Woodmizer sawmill
robinson46176 wrote:I was sorting some tools and stuff in the old shop today (yes, I am still moving) and was standing petting my Mark VII while planning its move. I was puttering with it and studying the fence when I noticed the miter gauge lock. In earlier discussions of the Mark VII I had forgotten the miter gauge lock. It has a cam lock instead of tightening a knob. The cam lock uses a "U" shaped lock that you can flip down with your thumbs assuming that you have worked carefully and have thumbs.
The fence of course also uses a cam lock. It has a rather long lever on it that "feels" good to me.
I am looking forward to getting it moved and lubed and putting it to work. Back when I bought it I had a lot of other stuff going on and had mostly just shoved it back in a corner since I didn't really need it and only used it a little.
.
I was in the old shop this evening and grabbed the Mark VII miter gauge and brought it to the house to take a couple of pictures.
This one is with the cam locked.
[ATTACH]16016[/ATTACH]
This one is with the cam unlocked.
[ATTACH]16017[/ATTACH]
This is a shot of the bottom. Does anyone know the story of the holes in the outer end of the bar? It is not reversible...
[ATTACH]16018[/ATTACH]
As you can see I have not cleaned the Mark VII up yet. When I picked the miter gauge up after the last picture the screw at the heel fell out. I thought it must have been loose but it looks like somebody stuck in one that is too short to tighten. I think I have a few new ones in my parts cabinet.
I should have grabbed the fence too and taken a picture of it.
.
Attachments
Mark VII miter gauge locked.JPG (73.92 KiB) Viewed 856 times
Mark VII miter gauge unlocked.JPG (85.4 KiB) Viewed 852 times
Mark VII miter gauge from bottom.JPG (75.42 KiB) Viewed 854 times
--
farmer
Francis Robinson
I did not equip with Shopsmiths in spite of the setups but because of them.
1 1988 - Mark V 510 (bought new), 4 Poly vee 1 1/8th HP Mark V's, Mark VII, 1 Mark V Mini, 1 Frankensmith, 1 10-ER, 1 Mark V Push-me-Pull-me Drillpress, SS bandsaw, belt sander, jointer, jigsaw, shaper attach, mortising attach, TS-3650 Rigid tablesaw, RAS, 6" long bed jointer, Foley/Belsaw Planer/molder/ripsaw, 1" sander, oscillating spindle/belt sander, Scroll saw, Woodmizer sawmill
That countersink hole in the end makes it easy to hang on a pegboard hook.
However I do not recall of a reason for it and the tapped hole.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
