No Double Tilt upgrade for model 500?

damagi · Post by **damagi** » Thu May 17, 2012 6:48 pm

SDSSmith wrote:Does the 500 fence work on a Mark VII table?

nope. last I checked the mkvii table is larger, almost the size of a 510 table.
inserts for the mk vii are the same as the 500

damagi · Post by **damagi** » Thu May 17, 2012 6:52 pm

[quote="easterngray"]Thanks very much for all your replies. It looks to me like the holes for the pins on the new tubes are on a different side of the tube than the 500 pins. If so, I guess you could just drill proper size holes on the proper side of the new tubes for the 500 configuration, and replace the pins with new ones.. yes? Damagi, as to the older Mark VII tables]

as noted below - yup

SDSSmith · Post by **SDSSmith** » Thu May 17, 2012 7:00 pm

damagi wrote:nope. last I checked the mkvii table is larger, almost the size of a 510 table.
inserts for the mk vii are the same as the 500

That is what I remembered, but could not verify since I have no Mark VII parts anymore.

robinson46176 · Post by **robinson46176** » Fri May 18, 2012 7:57 am

JPG40504 wrote:You took the words out of my mouth. AIUI the MVII table has the front rail like the M5/500 and is the same dimension front to rear. The rear clamp is lever actuated similar to a 510, but the clamp is the same(or very similar).

IF all that is correct, then it should.

Settle this Francis!:D You got the goods!!!!:rolleyes:

As has already been said now, while the table does have the same front rail it is longer front to rear (about 3") so the fences will not interchange. The table is about the same width as a 500 but with the "L" shaped extension slid into the right side it becomes a "lot" wider.
It would be kind of cool to have a second extension table with some length cut off of the post to clear the blade when slid in close.

I wasn't on here last night when this discussion was going on. As a family project and a mother's day gift our son and his wife came down and we built a new flower bed Diana had been wanting.

.

damagi · Post by **damagi** » Fri May 18, 2012 9:51 am

Ok, so apparently there is a question of the interchangability of the trunion to the Mark V table from the Mark VII. I will take a look and see when I get the chance

robinson46176 · Post by **robinson46176** » Fri May 18, 2012 11:13 am

robinson46176 wrote:I wasn't on here last night when this discussion was going on. As a family project and a mother's day gift our son and his wife came down and we built a new flower bed Diana had been wanting.

Here is last nights flower bed project...

[ATTACH]17411[/ATTACH]

.

JPG · Post by **JPG** » Sat May 19, 2012 12:21 am

damagi wrote:Ok, so apparently there is a question of the interchangability of the trunion to the Mark V table from the Mark VII. I will take a look and see when I get the chance

AIUI the rack is on the opposite side of the post.

damagi · Post by **damagi** » Mon May 28, 2012 2:59 am

In theory you could make a bracket to adapt the mark VII trunion to a mark V table or the other way around. the rack is on the opposite side of the trunion from the mark V version, but you certainly could flip the trunion around since its essentially symmetrical.

[ATTACH]17476[/ATTACH]

[ATTACH]17477[/ATTACH]

[ATTACH]17478[/ATTACH]

[ATTACH]17479[/ATTACH]

JPG · Post by **JPG** » Mon May 28, 2012 11:42 am

damagi wrote:In theory you could make a bracket to adapt the mark VII trunion to a mark V table or the other way around. the rack is on the opposite side of the trunion from the mark V version, but you certainly could flip the trunion around since its essentially symmetrical.

[ATTACH]17476[/ATTACH]

[ATTACH]17477[/ATTACH]

[ATTACH]17478[/ATTACH]

[ATTACH]17479[/ATTACH]

So, do I see separate trunion lock handles on the 'front' and 'rear'?

Indeed are there ANY differences between front and rear of the trunion?

If not, reversing would be a workable method.

easterngray · Post by **easterngray** » Tue May 29, 2012 5:27 pm

It just dawned on me... If I had a second 500 table in which the original support posts were removed, turned so the rack was on the opposite side and then re-mounted in the carriage, wouldn't that work with the double tilt kit as a dedicated under the table routing/shaping table? Thanks - Alec