Got to "look" at my Shopsmiths today...

Moderator: admin

User avatar
robinson46176
Platinum Member
Posts: 4182
Joined: Mon Mar 09, 2009 9:00 pm
Location: Central Indiana (Shelbyville)

Post by robinson46176 »

dusty wrote:I am very glad to hear all of this. I am sure we all are. However, don't get too cocky too soon. It sounds like you are pushing just a little bit. I gradually over came the damages that I caused but I got overly aggressive during my recovery and I paid a price. You don't want to go there.

I am still being quite careful... :cool: Sometimes when I say "we" it is because we are both out there. :rolleyes: Most of the time I should say "she" because she is the one doing the work... I'm just there to point and give instructions. :) I'm really good at pointing. :D :D
When "we" :) sat the new water tank (300 gal. Rubbermaid) the guy at the store put it in the truck and "she" unloaded it at home. Then when we found that it had a defect she called our daughter-in-law (lives at the north end of the farm) to help her load it back in the truck to return it for a good one. I was there so it was "we" :) but I was just pointing... "she" unloaded the replacement tank and slid it into position (in a fence line accessible from 2 lots) and dragged out a hose to fill it. At that point I was unnecessary even for pointing. :D Still, I was there. :)


.
--
farmer
Francis Robinson
I did not equip with Shopsmiths in spite of the setups but because of them.
1 1988 - Mark V 510 (bought new), 4 Poly vee 1 1/8th HP Mark V's, Mark VII, 1 Mark V Mini, 1 Frankensmith, 1 10-ER, 1 Mark V Push-me-Pull-me Drillpress, SS bandsaw, belt sander, jointer, jigsaw, shaper attach, mortising attach, TS-3650 Rigid tablesaw, RAS, 6" long bed jointer, Foley/Belsaw Planer/molder/ripsaw, 1" sander, oscillating spindle/belt sander, Scroll saw, Woodmizer sawmill
User avatar
dusty
Platinum Member
Posts: 21530
Joined: Wed Nov 22, 2006 6:52 am
Location: Tucson (Wildcat Country), Arizona

Post by dusty »

robinson46176 wrote:I am still being quite careful... :cool: Sometimes when I say "we" it is because we are both out there. :rolleyes: Most of the time I should say "she" because she is the one doing the work... I'm just there to point and give instructions. :) I'm really good at pointing. :D :D
When "we" :) sat the new water tank (300 gal. Rubbermaid) the guy at the store put it in the truck and "she" unloaded it at home. Then when we found that it had a defect she called our daughter-in-law (lives at the north end of the farm) to help her load it back in the truck to return it for a good one. I was there so it was "we" :) but I was just pointing... "she" unloaded the replacement tank and slid it into position (in a fence line accessible from 2 lots) and dragged out a hose to fill it. At that point I was unnecessary even for pointing. :D Still, I was there. :)


.
I think I understand. "We" are making a big pot of soup right now.

I peel and cut the potatoes, carrots, rutabaga, cabbage, onions, celery, etc. and I cut up and seared the meat. We are making soup.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
User avatar
dgale
Platinum Member
Posts: 1007
Joined: Fri Jul 13, 2012 1:17 am
Location: Dows Prairie, CA

Post by dgale »

dusty wrote:I think I understand. "We" are making a big pot of soup right now.

I peel and cut the potatoes, carrots, rutabaga, cabbage, onions, celery, etc. and I cut up and seared the meat. We are making soup.
I know that "we" very well - "we" got a whole lot of winterizing done around the property in the past month, while the other "we" seemed to get a lot of Facebook and Netflix viewing done...hopefully it won't take something as major as this on my front to tip those scales to a more collaborative equilibrium :rolleyes:

Glad to hear you are up and about and I'm sure the fresh air is helping with the healing. Also glad to hear you married a team player - make sure to get her an extra nice X-Mas present :)
'78 Mark V 500 #27995 (my Dad bought new)
'82 Mark V 500 #96309
Two '47 10E's (serial#4314+6149) - one a dedicated drill press and the other a lathe
Two 10E/ER in parts slowly being restored…#26822 and #????? (SS plate missing)
SPT's: Bandsaw, Belt Sander, Strip Sander, Jointer, Jigsaw, Biscuit Joiner
Post Reply