New bandsaw table not level
Moderator: admin
-
putttn
- Gold Member
- Posts: 410
- Joined: Sat Feb 17, 2007 11:44 am
- Location: Spokane, Wa Home of the ZAGS
- Contact:
New bandsaw table not level
Got a new aluminum bandsaw table and noticed the left rear corner is a good 1/16 low. Put my Woodpeckers 1281 on the table and its low in just that corner. I had the same problem with the cast iron table and thought this table would solve it. No such luck. I have the screw attach d in the rear middle groove. Dissappointing.
-
JPG
- Platinum Member
- Posts: 35457
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: New bandsaw table not level
Not level, or not flat?
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
putttn
- Gold Member
- Posts: 410
- Joined: Sat Feb 17, 2007 11:44 am
- Location: Spokane, Wa Home of the ZAGS
- Contact:
Re: New bandsaw table not level
Not flat. Lest rear corner is "sagging"
-
JPG
- Platinum Member
- Posts: 35457
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: New bandsaw table not level
How far from the corner is it 'not' sagging?putttn wrote:Not flat. Lest rear corner is "sagging"
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
putttn
- Gold Member
- Posts: 410
- Joined: Sat Feb 17, 2007 11:44 am
- Location: Spokane, Wa Home of the ZAGS
- Contact:
Re: New bandsaw table not level
starts sagging about 1" behind blabe and 1" to the left of the blade.
-
putttn
- Gold Member
- Posts: 410
- Joined: Sat Feb 17, 2007 11:44 am
- Location: Spokane, Wa Home of the ZAGS
- Contact:
Re: New bandsaw table not level
Just purchased it this year
-
JPG
- Platinum Member
- Posts: 35457
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: New bandsaw table not level
I think I would be disappointed as well. Have you discussed it with the mother ship?
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
putttn
- Gold Member
- Posts: 410
- Joined: Sat Feb 17, 2007 11:44 am
- Location: Spokane, Wa Home of the ZAGS
- Contact:
Re: New bandsaw table not level
Will do on Tues
Re: New bandsaw table not level
I have the same problem with my main table. A serious sag in the middle around the insert. I feel your pain.
PowerPro Mark 7, 11" Bandsaw, 4" Jointer, 12" Professional Planer, DC3300 Dust Collector, DW745, DW718 w/ DW723 and a DW788 w/ DW7880.
Success is not final, failure is not fatal: it is the courage to continue that counts. -Winston Churchill
Success is not final, failure is not fatal: it is the courage to continue that counts. -Winston Churchill
-
putttn
- Gold Member
- Posts: 410
- Joined: Sat Feb 17, 2007 11:44 am
- Location: Spokane, Wa Home of the ZAGS
- Contact:
Re: New bandsaw table not level
Seems like you couldnt get a square cut