[quote="JPG"]Could it possibly be that 'bolding' the "]" caused strange post? I will try that with this one.[/quote]
Looks strange to me!
510 Miter Gauge Problem
Moderator: admin
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: 510 Miter Gauge Problem
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: 510 Miter Gauge Problem
Oh and no I never had a locking set screw for the glide screws.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: 510 Miter Gauge Problem
==================JPG wrote:'Early' headless ones?Hobbyman2 wrote:Just for heads up,,, the replacement slotted glides i bought from SS are now black ,,, no longer white.
- 20170312_230859.jpg (118.88 KiB) Viewed 4125 times
Yea , the part number is on the bag ,,the x4 is not part of the number I ordered 4
Hobbyman2 Favorite Quote: "If a man does his best, what else is there?"
- General George S. Patton (1885-1945)
- General George S. Patton (1885-1945)
Re: 510 Miter Gauge Problem
I am wondering if the last guy didn't tighten a set screw down on the glides ,,mash out the threads and ruin the adjustment slot.
The new ones work like they are supposed to.
The new ones work like they are supposed to.
Hobbyman2 Favorite Quote: "If a man does his best, what else is there?"
- General George S. Patton (1885-1945)
- General George S. Patton (1885-1945)
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: 510 Miter Gauge Problem
Do use an appropriate size screw driver!Hobbyman2 wrote:I am wondering if the last guy didn't tighten a set screw down on the glides ,,mash out the threads and ruin the adjustment slot.
The new ones work like they are supposed to.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: 510 Miter Gauge Problem
I ground one down to custom fit!!
Hobbyman2 Favorite Quote: "If a man does his best, what else is there?"
- General George S. Patton (1885-1945)
- General George S. Patton (1885-1945)
Re: 510 Miter Gauge Problem
Well your new version is far different then mine. Just to prove that mine is in no way a tight fit I did a little video. When and if they will tighten it is due to the hex head, once you adjust them they don't stay in place, it takes just about zero effort to turn them. It is the same on the couple of this vintage that I have.........JPG wrote:My 'experience' with both versions* is that the nylon screws(both types) are a tight fit in the threaded hole and do not require a locking set screw.
What I do recommend for the stop rod set screw is a 1" long flat bottom set screw with a 5/32" hex socket.
That keeps crud out of the hole.
*yes I 'located' my 'newer' version. It is tapped through.
https://youtu.be/lI2cdDNEnCs
So am I just a lucky one or are other peoples ones the same?
Ed
{Knight of the Shopsmith} [Hero's don't wear capes, they wear dog tags]
Re: 510 Miter Gauge Problem
Thats pretty lose Ed.
Maybe you could wrap some teflon tape or some thing around the threads?
even after chasing my threads with a tap they are not that lose .
Maybe you could wrap some teflon tape or some thing around the threads?
even after chasing my threads with a tap they are not that lose .
Hobbyman2 Favorite Quote: "If a man does his best, what else is there?"
- General George S. Patton (1885-1945)
- General George S. Patton (1885-1945)
Re: 510 Miter Gauge Problem
From the couple of these that I have I think this is how they are. Waiting to see if others have the same experience. The slot headed ones are much tighter/snugger.Hobbyman2 wrote:Thats pretty lose Ed.
Maybe you could wrap some teflon tape or some thing around the threads?
even after chasing my threads with a tap they are not that lose .
I get these adjusted then tighten the metal set screw on them, not like a gorilla mind you, just to snug and that holds them fine. I'm sure thread locks of almost any non perminate type would work.
A shopsmith class I took many years ago they recommended this to keep the metal set screws from working loose and getting lost. Well either that or remove them and store them for whey you need them, which for me pretty much means I'd spend hours looking for them....
Ed
{Knight of the Shopsmith} [Hero's don't wear capes, they wear dog tags]
Re: 510 Miter Gauge Problem
So ,,,,,the set screw is supposed to tighten against plastic threads to keep the hex head screw from moving ?
I got it!
I got it!
Hobbyman2 Favorite Quote: "If a man does his best, what else is there?"
- General George S. Patton (1885-1945)
- General George S. Patton (1885-1945)