Last night/early early this morning, I had swapped out a 5/8 blade for a 3/8 on my bandsaw and was adjusting it when I ran into this problem. The blade guide adjusting knob is not adjusting the guide blocks. The blade is against the guide block bracket and turning the adjusting knobs does nothing. I am trying to center the blade on the guide blocks (back and forth)
I am never very good at explaining myself here. Attached is a photo which may make my problem more clear.
Any ideas what is the problem? Thanks in advance.
Bandsaw upper blade guide adj.
Moderator: admin
Bandsaw upper blade guide adj.
- Attachments
-
- IMG_0052.JPG (112.74 KiB) Viewed 8945 times
Re: Bandsaw upper blade guide adj.
That adjustment knob has a bolt running through it. My guess is the bolt is loose.
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Bandsaw upper blade guide adj.
Check to see if the screw is run out of the threads of the guide block? Try pushing the guides towards the adjusting knob while turning the knob(clockwise). You should be able to feel the screw threads engaging the threads in the guide block. The guide block is excessively extended in your pix. Be careful to not get it cross threaded.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
dusty
- Platinum Member
- Posts: 21530
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Bandsaw upper blade guide adj.
I have attached a couple images of my bandsaw (with no blade mounted) that may help to clarify the proposed solution (by others) that I suspect is right on. Excuse the saw dust, please. I use mine heavily and have no one to help keep the area clean.JAM831 wrote:Last night/early early this morning, I had swapped out a 5/8 blade for a 3/8 on my bandsaw and was adjusting it when I ran into this problem. The blade guide adjusting knob is not adjusting the guide blocks. The blade is against the guide block bracket and turning the adjusting knobs does nothing. I am trying to center the blade on the guide blocks (back and forth)
I am never very good at explaining myself here. Attached is a photo which may make my problem more clear.
Any ideas what is the problem? Thanks in advance.
- Bandsaw 007.jpg (1.08 MiB) Viewed 8839 times
- Bandsaw 008.jpg (1.13 MiB) Viewed 8839 times
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Bandsaw upper blade guide adj.
Dusty: Your photographic skills have definitely improved!!!!!
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
dusty
- Platinum Member
- Posts: 21530
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Bandsaw upper blade guide adj.
Thanks for the complement but it is not my "skill" that has improved. It is the camera. I have retired my old camera and am not using my Samsung Galaxy for all photographic work.JPG wrote:Dusty: Your photographic skills have definitely improved!!!!!
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
Re: Bandsaw upper blade guide adj.
Hey all. Thanks for the ideas. I forgot I had asked my question in here. I took the adjustment assembly off and put it back on and it worked. So I reckon y'alls advice was right and I just got lucky and fixed it before reading the posts.
Re: Bandsaw upper blade guide adj.
unrelated question to @dusty.
are the guide block you have shown here called "cool" block? or regular block or ceramic block?
and yes! i definitely see your photo quality has been improved :-)
are the guide block you have shown here called "cool" block? or regular block or ceramic block?
and yes! i definitely see your photo quality has been improved :-)
dusty wrote:I have attached a couple images of my bandsaw (with no blade mounted) that may help to clarify the proposed solution (by others) that I suspect is right on. Excuse the saw dust, please. I use mine heavily and have no one to help keep the area clean.JAM831 wrote:Last night/early early this morning, I had swapped out a 5/8 blade for a 3/8 on my bandsaw and was adjusting it when I ran into this problem. The blade guide adjusting knob is not adjusting the guide blocks. The blade is against the guide block bracket and turning the adjusting knobs does nothing. I am trying to center the blade on the guide blocks (back and forth)
I am never very good at explaining myself here. Attached is a photo which may make my problem more clear.
Any ideas what is the problem? Thanks in advance.
Bandsaw 007.jpgBandsaw 008.jpg