Is "Powertool Woodworking For Everyone" also for Mark 7?

[the1avi]

I also was just looking at my book and noticed that there was another section called "Under Table Routing and Shaping with the Double-Tilt System" that I seem to recall being missing in the other manual. You might want to see if you have a similar section or have it under another name...... Pages are labeled B-1 thru B-22.
Ed

I have the following sections:

• A[1-12]: Safety and Electrical requirements
• B[1-16]: Terms, parts lists, and exploded views
• C[1-32]: Unpacking, alignment, mode setups
• D[-47]: Powerpro headstock operations, table sawing, disc sanding, vertical drilling, horizontal boring, lathe turning, under-table shaping, pin shaping and routing, over-table routing
• E[1-33]: Maintenance and troubleshooting

As far as I can tell, there is nothing about shaping with the double-tilt system.

[JPG]

I also was just looking at my book and noticed that there was another section called "Under Table Routing and Shaping with the Double-Tilt System" that I seem to recall being missing in the other manual. You might want to see if you have a similar section or have it under another name...... Pages are labeled B-1 thru B-22.
Ed

I have the following sections:

• A[1-12]: Safety and Electrical requirements
• B[1-16]: Terms, parts lists, and exploded views
• C[1-32]: Unpacking, alignment, mode setups
• D[-47]: Powerpro headstock operations, table sawing, disc sanding, vertical drilling, horizontal boring, lathe turning, under-table shaping, pin shaping and routing, over-table routing
• E[1-33]: Maintenance and troubleshooting

As far as I can tell, there is nothing about shaping with the double-tilt system.

??????

[the1avi]

I also was just looking at my book and noticed that there was another section called "Under Table Routing and Shaping with the Double-Tilt System" that I seem to recall being missing in the other manual. You might want to see if you have a similar section or have it under another name...... Pages are labeled B-1 thru B-22.
Ed

I have the following sections:

• A[1-12]: Safety and Electrical requirements
• B[1-16]: Terms, parts lists, and exploded views
• C[1-32]: Unpacking, alignment, mode setups
• D[-47]: Powerpro headstock operations, table sawing, disc sanding, vertical drilling, horizontal boring, lathe turning, under-table shaping, pin shaping and routing, over-table routing
• E[1-33]: Maintenance and troubleshooting

As far as I can tell, there is nothing about shaping with the double-tilt system.

??????

What I meant is that it doesn't mention the double-tilt system.

[jsburger]

I have the following sections:

• A[1-12]: Safety and Electrical requirements
• B[1-16]: Terms, parts lists, and exploded views
• C[1-32]: Unpacking, alignment, mode setups
• D[-47]: Powerpro headstock operations, table sawing, disc sanding, vertical drilling, horizontal boring, lathe turning, under-table shaping, pin shaping and routing, over-table routing
• E[1-33]: Maintenance and troubleshooting

As far as I can tell, there is nothing about shaping with the double-tilt system.

??????

What I meant is that it doesn't mention the double-tilt system.

Maybe they thought it is a given since you can't do under table shaping without the double tilt system. The MK 7 is double tilt by default.

[JPG]

Default makes sense.

[chapmanruss]

I bought the Mark 7 manual recently after upgrading my Mark V 520 to a Mark 7. This is the manual I received.

Notebook cover

IMG_1216r.jpg (309.66 KiB) Viewed 14046 times

Inside first page

IMG_1217r.jpg (264.1 KiB) Viewed 14046 times

[the1avi]

My cover is different but the book itself seems the same based on your first page.