Another Day at The Office

[mbcabinetmaker]

1.jpg (337.61 KiB) Viewed 14625 times

Drawer runner drilling jig.

2.jpg (329.42 KiB) Viewed 14625 times

3.jpg (306.04 KiB) Viewed 14625 times

Remember this you'll need it later.

[mbcabinetmaker]

1.jpg (333.15 KiB) Viewed 14592 times

See I told you. Pre drilling as many things as you can before assembly makes things go a lot faster.

2.jpg (396.82 KiB) Viewed 14592 times

Time to set the drawers and doors to finish the island.

4 (2).jpg (373.04 KiB) Viewed 14592 times

This is a base I built while you wern't looking.

4 (1).jpg (393.25 KiB) Viewed 14592 times

This consist of 3 cabinets, two panel ends and a back panel along with the base.

[mbcabinetmaker]

1.jpg (397.71 KiB) Viewed 14587 times

2.jpg (425.49 KiB) Viewed 14587 times

3.jpg (246.91 KiB) Viewed 14587 times

Looks almost as good as my Sketchup model.

4.jpg (261.7 KiB) Viewed 14587 times

If you use Sketchup and haven't tried Sketchup Viewer it is hand to have on a tablet or phone for shop reference.

5.jpg (368.17 KiB) Viewed 14587 times

Up next

[Billdit]

Mark, you do the best work ! Good seeing you take the time to share your expertise ! Is your “new” Powerpro unit still getting it done ?

[mbcabinetmaker]

Mark, you do the best work ! Good seeing you take the time to share your expertise ! Is your “new” Powerpro unit still getting it done ?

Yes Bill it hasn't given me any trouble and I use it for something almost daily. Love the power and smoothness!

[WileyCoyote]

It is so nice seeing these units come together. I hope you show them after the finish has been applied, too. They look awesome and I wish I had the skill to do the quality work you do (and your awesome shop).

[mbcabinetmaker]

It is so nice seeing these units come together. I hope you show them after the finish has been applied, too. They look awesome and I wish I had the skill to do the quality work you do (and your awesome shop).

I'll try to get pictures but 99% of the work that I do these days is for a larger shop. I build the jobs and drop them off to their finishing shop and they take it from there. I rarely get out to a job site which is fine with me!

[mbcabinetmaker]

1.jpg (304.83 KiB) Viewed 14509 times

It seems like Rev a Shelf changes these about every year or so so my old template no longer works with the new hardware.

2.jpg (335 KiB) Viewed 14509 times

No problem I'll just glue the new template to a board and save it until the next change.

3.jpg (357.71 KiB) Viewed 14509 times

4.jpg (342.09 KiB) Viewed 14509 times

Next step is to drill 1/4" holes in the template on the Mark 7 to accommodate a Vix bit.

5.jpg (414.84 KiB) Viewed 14509 times

And finally cut the notch in the template to align with the front of the cabinet.

[mbcabinetmaker]

a.jpg (314.53 KiB) Viewed 14504 times

Now we can drill for the Lazy Susan hardware.

2.jpg (403.89 KiB) Viewed 14504 times

3.jpg (306.82 KiB) Viewed 14504 times

4.jpg (371.45 KiB) Viewed 14504 times

The lower hinges have to be offset to clear the bottom tray.

[mbcabinetmaker]

1.jpg (321.25 KiB) Viewed 14460 times

Here I fit the backs but they will be installed after painting is done.

2.jpg (410.85 KiB) Viewed 14460 times

A little specility drilling for the doors.

3.jpg (351.64 KiB) Viewed 14460 times

No it just looks like a mistake!

4.jpg (365.79 KiB) Viewed 14460 times

This is called a bi-fold hinge.

5.jpg (335.56 KiB) Viewed 14460 times

All ready to install onto the cabinet.