what's the spindle knob for?
Moderator: admin
-
JPG
- Platinum Member
- Posts: 35430
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: what's the spindle knob for?
BTW read this https://www.shopsmith.com/ss_forum/comm ... 19246.html
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: what's the spindle knob for?
- C1EA51C9-0B48-48EF-A882-3CC0979629FF.jpeg (47.71 KiB) Viewed 2975 times
- C1EA51C9-0B48-48EF-A882-3CC0979629FF.jpeg (47.71 KiB) Viewed 2975 times
- B81D334B-0CAC-4457-8785-06B7F2380BF4.jpeg (43.53 KiB) Viewed 2975 times
Re: what's the spindle knob for?
Weird retaining rings, not lock washers. Sorry. There’s one in the back? On the inside? Going to look now. I was wondering where that one went. Lol
Re: what's the spindle knob for?
- C57368A1-3FF1-462F-901C-0B44AFC24347.jpeg (87.61 KiB) Viewed 2975 times
Here??? I don’t see a groove for it.
Re: what's the spindle knob for?
Nevermind. I see / feel it. I’ll remove the drive sleeve, install the back one, reinstall, and put the front one back in place. That should solve that issue. Now to find that collar
Re: what's the spindle knob for?
How bout that! I was actually able to get it seated in without removing the drive sleeve.
-
JPG
- Platinum Member
- Posts: 35430
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: what's the spindle knob for?
Good Boy! Now talk to Tony!
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: what's the spindle knob for?
https://rover.ebay.com/rover/0/0/0?mpre ... 1239479973
Will this work if I can’t find / order a new collar?
Will this work if I can’t find / order a new collar?
-
JPG
- Platinum Member
- Posts: 35430
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: what's the spindle knob for?
NO.Jkroofer wrote:https://rover.ebay.com/rover/0/0/0?mpre ... 1239479973
Will this work if I can’t find / order a new collar?
FWIW I just bought 10 unplated for $0.64 each for a different purpose.
The knurled collar has an extension that bears against the inner race of the bearing and thus acts as a shaft end play preventer.
Repeat the Tony mantra and give him more time to reveal the location of the errant collar.
Fear not there are other sources. (used)
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: what's the spindle knob for?
I remember seeing a post that shows that there are differences between the collars of the older single bearing quill and the 2 bearing quill that I have. I found one used on eBay and purchased it as it was fairly inexpensive but I’m not sure which one it is. I guess I have a 50/50 shot of getting the right one. Tony has unfortunately been no help. If you know where I can purchase one and be confident that it’s the correct part, can you send me a link?