Mark V Speed Control
Moderators: HopefulSSer, admin
Re: Mark V Speed Control
What jumps out at me is that your measured values look a lot like mine but from measuring the Idler, not the Main. Your stated motor speed (5480) is, I presume a typo? 3580 is more realistic. (Or is that the problem?) If I'm understanding your data correctly, your high and low speeds are even high compared to BuckeyeDennis earlier in the thread. I've thought about his numbers, 1055 and 6533, but don't have a theory.
- David
- David
- dusty
- Platinum Member
- Posts: 21371
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Mark V Speed Control
3580 it is. I corrected my previous post.DLB wrote: ↑Thu Aug 11, 2022 4:04 pm What jumps out at me is that your measured values look a lot like mine but from measuring the Idler, not the Main. Your stated motor speed (5480) is, I presume a typo? 3580 is more realistic. (Or is that the problem?) If I'm understanding your data correctly, your high and low speeds are even high compared to BuckeyeDennis earlier in the thread. I've thought about his numbers, 1055 and 6533, but don't have a theory.
- David
You are also correct in that the measured speeds were those of the idler shaft.
Thanks for the corrections. I also found that my drive belt is not 27" as I had thought. It is actually 26 5/8" top measurement.
Thanks for keeping me honest. This whole thing is beginning to come together.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
Re: Mark V Speed Control
Your numbers look very much like mine then. Generally within 10% of the table, with everything on the high side. My impression of mine is that I can do a tachometer assisted calibration of the indicator dial and move everything, or at least the speeds I use, to within 5%.dusty wrote: ↑Thu Aug 11, 2022 6:01 pm 3580 it is. I corrected my previous post.
You are also correct in that the measured speeds were those of the idler shaft.
Thanks for the corrections. I also found that my drive belt is not 27" as I had thought. It is actually 26 5/8" top measurement.
Thanks for keeping me honest. This whole thing is beginning to come together.
- David
- dusty
- Platinum Member
- Posts: 21371
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Mark V Speed Control
I sure hope the OPs questions have been answered.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
- dusty
- Platinum Member
- Posts: 21371
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Mark V Speed Control
Hope this becomes as useful for others as it did for me.
It is an Excel spreadsheet that can be used to determine shaft speeds given different size sheaves , Included are the formulae for each of the cells in the spread sheet (very useful if you make an inappropriate entry into a cell); doing so could really alter the results.
When using this, I typically enter sheave size into E23 and then copy and paste into C3. Users Choice.
Change motor speed to whatever motor speed may be of interest and then center 1.9894321 into E23. This should give you shaft speeds for when the upper sheave and lower sheave are the "same size".
It is an Excel spreadsheet that can be used to determine shaft speeds given different size sheaves , Included are the formulae for each of the cells in the spread sheet (very useful if you make an inappropriate entry into a cell); doing so could really alter the results.
When using this, I typically enter sheave size into E23 and then copy and paste into C3. Users Choice.
Change motor speed to whatever motor speed may be of interest and then center 1.9894321 into E23. This should give you shaft speeds for when the upper sheave and lower sheave are the "same size".
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
- dusty
- Platinum Member
- Posts: 21371
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Mark V Speed Control
Thank you, DLB. Dave pointed out an error in the previous posted. The formula in C19 will most commonly be C18/1.6. Sorry about the confusion that that might have caused.
I have changed my spead sheet some and will post it here as well. Please understand that this was a toy developed to help me better understand the relationship if the sheaves when the size of the drive sheave (C8) is altered.
Another
I have changed my spead sheet some and will post it here as well. Please understand that this was a toy developed to help me better understand the relationship if the sheaves when the size of the drive sheave (C8) is altered.
Another
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
- dusty
- Platinum Member
- Posts: 21371
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Mark V Speed Control
Are the various dimensions of the sheaves "critical" to the operation of of the "speed control mechanism" of the Shopsmith. I have recently had access to six different sets of sheaves and I find that they vary significantly in size. These came from an individual who had been parting out, repairing and selling Mark 5's as assemblies and for parts. Thus the sheaves may be questionable samples.
What do y'all think?
I believe that they need to, as a minimum, being matching pairs!!
What do y'all think?
I believe that they need to, as a minimum, being matching pairs!!
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
- JPG
- Platinum Member
- Posts: 34648
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Mark V Speed Control
Question is, WHAT dimensions vary?
I think other than bore/fit etc., the slope of the bevel dimensions from the center axis is the only thing.
That said, as sloppy as a reeves drive is what does it matter?
I think other than bore/fit etc., the slope of the bevel dimensions from the center axis is the only thing.
That said, as sloppy as a reeves drive is what does it matter?
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
- dusty
- Platinum Member
- Posts: 21371
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Mark V Speed Control
Just about every dimension other than the bore - particularly the outer diameter and the length of the vanes and the angle of the slope..
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
- JPG
- Platinum Member
- Posts: 34648
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Mark V Speed Control
The vanes should not come into play except for the control sheave, then their distance from the button bearing end matters(where the pork chop touches).
The od is minor since it only comes into play when the belt is OVER extended on the pulley.
The od is minor since it only comes into play when the belt is OVER extended on the pulley.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange