I purchased a Shopsmith with a lot of accessories and the item in the photo I can't identify. Does anyone know how to use this part? There are not any numbers on it.
Thanks,
Doug
Shopsmith Accessory
Moderators: HopefulSSer, admin
Shopsmith Accessory
- Attachments
-
- Shopsmith Part.jpg (205.99 KiB) Viewed 4106 times
Re: Shopsmith Accessory
I don't recognize it right off. On the end shown, is the hole 5/8" ID? What does the other end look like? What version or model of Shopsmith do you have?
Welcome to the forum and the world of Shopsmith!
- David
Re: Shopsmith Accessory
Is that piece from a mortising tool?
Ed from Rhode Island
510 PowerPro Double Tilt:Greenie PowerPro Drill Press:500 Sanding Shorty w/Belt&Strip Sanders
Super Sawsmith 2000:Scroll Saw w/Stand:Joint-Matic:Power Station:Power Stand:Bandsaw:Joiner:Jigsaw
1961 Goldie:1960 Sawsmith RAS:10ER
510 PowerPro Double Tilt:Greenie PowerPro Drill Press:500 Sanding Shorty w/Belt&Strip Sanders
Super Sawsmith 2000:Scroll Saw w/Stand:Joint-Matic:Power Station:Power Stand:Bandsaw:Joiner:Jigsaw
1961 Goldie:1960 Sawsmith RAS:10ER
- BuckeyeDennis
- Platinum Member
- Posts: 3697
- Joined: Tue Jul 24, 2012 10:03 pm
- Location: Central Ohio
Re: Shopsmith Accessory
Exactly correct ED. This is one of the accessories I have not used yet. Thanks for the info.
Doug
Doug
-
- Gold Member
- Posts: 22
- Joined: Mon Oct 09, 2023 7:02 pm
Re: Shopsmith Accessory
I had the same question, thanks for explaining.
- chapmanruss
- Platinum Member
- Posts: 3488
- Joined: Tue Aug 26, 2014 8:16 pm
- Location: near Portland, Oregon
Re: Shopsmith Accessory
Just for reference the picture below shows complete Mortises and the Hold-downs starting with the one for the Model 10's (left), Mark 5 Greenies (center) and the current set (right). Other than color for the Greenie and the Goldie (not shown) there is very little difference between them. The Cap and Set Screws changed from using a 3/16" Allen Wrench to the 5/32" Allen Wrench with the introduction of the Mark 5 in 1954. The black protective coating, as seen on Doug's Sleeve above, was added beginning in 1964. The casting for the Hold-down changed on the newer ones along with the addition of the "T" slot nut for Mark models other than the original Mark 5/V 500 Table/Fence system, Mark 2 and 1960's Mark VII. Any of the different era Mortises will work on any Shopsmith. The Hold-down which attaches to the Fence on all models needs the "T" nut for use on the Mark V 510/505, 520, Mark 7, Mark 4 and the upgrade Mark V 500 Fence with the "T" slot.
_ .
For reference a PDF copy instruction sheet from the Model 10 era is below. Setup and use will be similar on Mark models.
_
_ .
For reference a PDF copy instruction sheet from the Model 10 era is below. Setup and use will be similar on Mark models.
_
Russ
Mark V completely upgraded to Mark 7
Mark V 520
All SPT's & 2 Power Stations
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored. Others to be restored.
Mark V completely upgraded to Mark 7
Mark V 520
All SPT's & 2 Power Stations
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored. Others to be restored.