Stand alone router table
Moderators: HopefulSSer, admin
Well, guess what...I laid a long level down on the router table yesterday evening. Came back a couple minutes later to pick the level up, saw light under the level midway. Turns out my router table surface dips down between 1/8 and 3/16 of an inch. Don't know for sure about the measurement. Didn't check it.
This is the table itself. Not the router plate. I only have a PC6902 under it. Never sat anything heavy on it. Maybe my father did before he gave it to me. Can't say I ever checked it.
What am I to do? New table?
This is the table itself. Not the router plate. I only have a PC6902 under it. Never sat anything heavy on it. Maybe my father did before he gave it to me. Can't say I ever checked it.
What am I to do? New table?
-
- Gold Member
- Posts: 240
- Joined: Thu Jul 20, 2006 12:55 pm
- Location: Greenville, SC
Before you ditch it, you might try adding some braces to the underside. One of the Woodworking mags (can't remember which one) had an article this month about checking your router table.
Their solution to a dip in the middle was to add 2 prefectly straight (jointed) boards on edge underneath the table. As you fasten the boards with screws, they should pull the table back flat. (At least, that's the theory.)
Their solution to a dip in the middle was to add 2 prefectly straight (jointed) boards on edge underneath the table. As you fasten the boards with screws, they should pull the table back flat. (At least, that's the theory.)
Doug
Greenville, SC
Greenville, SC
Router Table
Over the years I have built several router tables and have yet to build the perfect one. The under table will do some things quite well and the over arm
OPR can do many things well. I have both so I usually get the job done. I have never posted pictures so I will try it now with the last router table built and the one I use today. If you have any interest or want some info on the table give me a ping. I see I can only put five atachments with this post I will try and get the rest in another post.
ldh
OPR can do many things well. I have both so I usually get the job done. I have never posted pictures so I will try it now with the last router table built and the one I use today. If you have any interest or want some info on the table give me a ping. I see I can only put five atachments with this post I will try and get the rest in another post.
ldh
- Attachments
-
- DSCN1176.JPG (81.68 KiB) Viewed 12952 times
-
- DSCN1177.JPG (83.24 KiB) Viewed 12933 times
-
- DSCN1178.JPG (57.48 KiB) Viewed 12931 times
-
- DSCN1179.JPG (66.77 KiB) Viewed 12924 times
-
- DSCN1181.JPG (78.07 KiB) Viewed 12926 times
Router table
The remaining jpgs
ldh
ldh
- Attachments
-
- DSCN1183.JPG (72 KiB) Viewed 12927 times
-
- DSCN1184.JPG (58.91 KiB) Viewed 12919 times
-
- DSCN1185.JPG (53.38 KiB) Viewed 12916 times
-
- DSCN1186.JPG (56.2 KiB) Viewed 12913 times
-
- DSCN1187.JPG (54.99 KiB) Viewed 12921 times
-
- Gold Member
- Posts: 240
- Joined: Thu Jul 20, 2006 12:55 pm
- Location: Greenville, SC
Doug,
The caster set is from a SS 10ER from the 1950s. I like to use them as they work well on straight legs. You can use the Mark V casters, but then you have to weld up an angled bracket to attach them to straight legs. The steel wheels on the set were replaced with urethane wheels to handle the weight of the table. The frame of the router table is of .065 x 1 1/4 tube steel.
The sled is a jig to make 1/4, 3/8 and 1/2" box joints. It follows the respective PC guide mounted in the router plate. It is adjustable to take up any play in both the guide and adjustment of the pins. Works quite well. I like to make boxes. I also have a jig that fits my Mark V that uses a dado blade and is fully adjustable. If there is any interest I will post a pic.
ldh
The caster set is from a SS 10ER from the 1950s. I like to use them as they work well on straight legs. You can use the Mark V casters, but then you have to weld up an angled bracket to attach them to straight legs. The steel wheels on the set were replaced with urethane wheels to handle the weight of the table. The frame of the router table is of .065 x 1 1/4 tube steel.
The sled is a jig to make 1/4, 3/8 and 1/2" box joints. It follows the respective PC guide mounted in the router plate. It is adjustable to take up any play in both the guide and adjustment of the pins. Works quite well. I like to make boxes. I also have a jig that fits my Mark V that uses a dado blade and is fully adjustable. If there is any interest I will post a pic.
ldh
- dusty
- Platinum Member
- Posts: 21374
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Box Joint Jig
idh
Please do post the pics. There is always interest.
Please excuse me for being a peeping woodworker but you shop looks quite interesting and amazingly organized. Really like your choice of equipment, what I could steal a peak at.
Please do post the pics. There is always interest.
Please excuse me for being a peeping woodworker but you shop looks quite interesting and amazingly organized. Really like your choice of equipment, what I could steal a peak at.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.