Page 2 of 2
Re: Is "Powertool Woodworking For Everyone" also for Mark 7?
Posted: Sun Jul 22, 2018 2:55 pm
by the1avi
reible wrote:
I also was just looking at my book and noticed that there was another section called "Under Table Routing and Shaping with the Double-Tilt System" that I seem to recall being missing in the other manual. You might want to see if you have a similar section or have it under another name...... Pages are labeled B-1 thru B-22.
Ed
I have the following sections:
- A[1-12]: Safety and Electrical requirements
- B[1-16]: Terms, parts lists, and exploded views
- C[1-32]: Unpacking, alignment, mode setups
- D[-47]: Powerpro headstock operations, table sawing, disc sanding, vertical drilling, horizontal boring, lathe turning, under-table shaping, pin shaping and routing, over-table routing
- E[1-33]: Maintenance and troubleshooting
As far as I can tell, there is nothing about shaping with the double-tilt system.
Re: Is "Powertool Woodworking For Everyone" also for Mark 7?
Posted: Sun Jul 22, 2018 3:23 pm
by JPG
the1avi wrote:reible wrote:
I also was just looking at my book and noticed that there was another section called "Under Table Routing and Shaping with the Double-Tilt System" that I seem to recall being missing in the other manual. You might want to see if you have a similar section or have it under another name...... Pages are labeled B-1 thru B-22.
Ed
I have the following sections:
- A[1-12]: Safety and Electrical requirements
- B[1-16]: Terms, parts lists, and exploded views
- C[1-32]: Unpacking, alignment, mode setups
- D[-47]: Powerpro headstock operations, table sawing, disc sanding, vertical drilling, horizontal boring, lathe turning, under-table shaping, pin shaping and routing, over-table routing
- E[1-33]: Maintenance and troubleshooting
As far as I can tell, there is nothing about shaping with the double-tilt system.
??????
Re: Is "Powertool Woodworking For Everyone" also for Mark 7?
Posted: Sun Jul 22, 2018 4:25 pm
by the1avi
JPG wrote:the1avi wrote:reible wrote:
I also was just looking at my book and noticed that there was another section called "Under Table Routing and Shaping with the Double-Tilt System" that I seem to recall being missing in the other manual. You might want to see if you have a similar section or have it under another name...... Pages are labeled B-1 thru B-22.
Ed
I have the following sections:
- A[1-12]: Safety and Electrical requirements
- B[1-16]: Terms, parts lists, and exploded views
- C[1-32]: Unpacking, alignment, mode setups
- D[-47]: Powerpro headstock operations, table sawing, disc sanding, vertical drilling, horizontal boring, lathe turning, under-table shaping, pin shaping and routing, over-table routing
- E[1-33]: Maintenance and troubleshooting
As far as I can tell, there is nothing about shaping with the double-tilt system.
??????
What I meant is that it doesn't mention the double-tilt system.
Re: Is "Powertool Woodworking For Everyone" also for Mark 7?
Posted: Sun Jul 22, 2018 4:58 pm
by jsburger
the1avi wrote:JPG wrote:the1avi wrote:
I have the following sections:
- A[1-12]: Safety and Electrical requirements
- B[1-16]: Terms, parts lists, and exploded views
- C[1-32]: Unpacking, alignment, mode setups
- D[-47]: Powerpro headstock operations, table sawing, disc sanding, vertical drilling, horizontal boring, lathe turning, under-table shaping, pin shaping and routing, over-table routing
- E[1-33]: Maintenance and troubleshooting
As far as I can tell, there is nothing about shaping with the double-tilt system.
??????
What I meant is that it doesn't mention the double-tilt system.
Maybe they thought it is a given since you can't do under table shaping without the double tilt system. The MK 7 is double tilt by default.
Re: Is "Powertool Woodworking For Everyone" also for Mark 7?
Posted: Sun Jul 22, 2018 5:45 pm
by JPG
Default makes sense.
Re: Is "Powertool Woodworking For Everyone" also for Mark 7?
Posted: Mon Jul 23, 2018 2:06 pm
by chapmanruss
I bought the Mark 7 manual recently after upgrading my Mark V 520 to a Mark 7. This is the manual I received.
- Notebook cover
- IMG_1216r.jpg (309.66 KiB) Viewed 14052 times
- Inside first page
- IMG_1217r.jpg (264.1 KiB) Viewed 14052 times
Re: Is "Powertool Woodworking For Everyone" also for Mark 7?
Posted: Mon Jul 23, 2018 9:21 pm
by the1avi
My cover is different but the book itself seems the same based on your first page.