Page 2 of 3
Posted: Wed Apr 20, 2011 1:17 pm
by jm51
Safety issues aside, imo those vids showed the potential of a SS much better than the 3 part SS demo on youtube.
I didn't realise that making box joints was so easy although seeing him cutting the 8 x 4 sheet made a good advert for guide rail saws.
Posted: Wed Apr 20, 2011 2:05 pm
by ddvann79
jm51 wrote:I didn't realise that making box joints was so easy...
That's the method illustrated in PTWFE
here. You just have to make sure your pin distance is dead on.
Posted: Wed Apr 20, 2011 4:44 pm
by dusty
I sure hope that guy still has all of his fingers. Doing what he is demonstrating with no push blocks or push sticks just makes my skin crawl.
I enjoy the videos and they provide a lot of good information but definitely ignore safety practices.
Now - I am off to use my Multipurpose Power Tool.
Posted: Wed Apr 20, 2011 4:57 pm
by heathicus
dusty wrote:I sure hope that guy still has all of his fingers. Doing what he is demonstrating with no push blocks or push sticks just makes my skin crawl.
I enjoy the videos and they provide a lot of good information but definitely ignore safety practices.
Now - I am off to use my Multipurpose Power Tool.
You mean your
Modern Multipurpose Power Tool?
Posted: Wed Apr 20, 2011 5:14 pm
by mrhart
[quote="heathicus"]You mean your Modern Multipurpose Power Tool? ]
"Todays" Modern Multipurpose Power Tool
Posted: Wed Apr 20, 2011 5:32 pm
by JPG
mrhart wrote:"Todays" Modern Multipurpose Power Tool
Dusty doesn't have a PP (yet)!;) Nor do I.
About safety...
Posted: Wed Apr 20, 2011 5:40 pm
by tomsalwasser
The thing to remember is these films were made 60 years ago. Safety practices evolve. I'm sure 60 years from now people will look back and shake their heads at how unsafe the things we do in our shops today are.
I hope you're all enjoying these great old films as much as I do. But enough of my blathering, I have work to do.
Coming soon to a computer near you...the next installment of Vintage PTWFE: Drill Press and Drilling
Posted: Wed Apr 20, 2011 6:16 pm
by robinson46176
dusty wrote:OKAY I did that Tom. Three times.
I hope these films were made before push sticks and push blocks. It scares me every time he gets close to the blade and even more when he passes his hand over the blade while cutting dados and using the shaper.
My first cringe was when he cut those spline slots in those little narrow pieces with his fingers pushing them against the fence right down at the blade level.
There were others. I also noticed that sometimes he appeared to be pushing with the miter gauge with one hand and maybe pushing with the other hand on the board on the other side of the blade. Good way to pinch the blade...
Posted: Wed Apr 20, 2011 11:10 pm
by dlbristol
Interesting stuff! It sure did show some of the precision possible with the SS. I thought the way he cut a dado was a little scary. I would not have ever thought of doing what he did. I have cut each side and then nibbled out the middle one pass at a time, but moving the blade in and out never occurred to me. Probably a good thing.
Posted: Thu Apr 21, 2011 12:16 am
by JPG
[quote="dlbristol"]Interesting stuff! It sure did show some of the precision possible with the SS. I thought the way he cut a dado was a little scary. I would not have ever thought of doing what he did. I have cut each side and then nibbled out the middle one pass at a time, but moving the blade in and out never occurred to me. Probably a good thing.]
The quill fed blade to clean up a wide cut was de rigor in the demos even in the 60's.
One thing I noticed was he must have taught Norm technique, since he had a tendency to not hold the workpiece tight to the table top.
I think camera angle made some things appear more scarier. We could not see how far his pinkies were from the edge of the workpiece. A couple of places it looked like he was very close!!!
I look forward to the chapters to come.
Thank You for sharing them!
Gotta wonder where ya latched on to them!