Shopsmith Forums

Posted: **Sat Oct 08, 2011 9:18 am**

Here are some of the pens that I have made.
[ATTACH]14444[/ATTACH]

[ATTACH]14445[/ATTACH]

[ATTACH]14446[/ATTACH]
Bill V

Posted: **Sat Oct 08, 2011 10:49 am**

I had no idea... I'm amazed! thank you for the feed back and great examples too...

Posted: **Sat Oct 08, 2011 11:45 am**

Here's Nick's approach: http://www.shopsmithacademy.com/SS_Archives/SS108/SS108_Turning_Pens.htm

Here's the Penn State mandrel I use:
http://www.pennstateind.com/store/PKM-CL.html

I use this live-center set from Woodcraft:
http://www.woodcraft.com/Product/2003727/1576/Pro-Live-Center-Set-2-Morse-Taper-Pro-Set.aspx

Posted: **Sat Oct 08, 2011 4:23 pm**

bffulgham wrote:Here's Nick's approach: http://www.shopsmithacademy.com/SS_Archives/SS108/SS108_Turning_Pens.htm http://www.woodcraft.com/Product/2003727/1576/Pro-Live-Center-Set-2-Morse-Taper-Pro-Set.aspx

A useful demo.

I looked for the fence that Nick used for horizontal boring, but couldn't find it specifically on the SS accessories site. Do you know if that's a standard SS accessory?

Posted: **Sat Oct 08, 2011 5:35 pm**

wurlitzerwilly wrote:A useful demo.

I looked for the fence that Nick used for horizontal boring, but couldn't find it specifically on the SS accessories site. Do you know if that's a standard SS accessory?

I checked out the penturning video (Sawdust Session) to see which fence you are asking about. I think this linkto the catalog may answer your question. The fence is an accessory to the miter gauge.

Hope this helps.

Posted: **Sat Oct 08, 2011 7:49 pm**

dusty wrote:I checked out the penturning video (Sawdust Session) to see which fence you are asking about. I think this linkto the catalog may answer your question. The fence is an accessory to the miter gauge.

Hope this helps.

I'm not sure. The fence in the video looks more solid like the 520 upgrade fence, but maybe shorter.

I'll check out the video again for a closer look.

Posted: **Sun Oct 09, 2011 12:10 am**

[ATTACH]14448[/ATTACH]

Upper left (F)

Posted: **Sun Oct 09, 2011 5:13 am**

JPG40504 wrote:[ATTACH]14448[/ATTACH]

Upper left (F)

A picture's worth a thousand words.

I musta had a really senior moment, it's so obvious and you're both right. I was looking at the one above with the wood block, which is what Nick had mounted and I selectively ignored the correct fence image.

I think I need to buy the kit.

Posted: **Sun Oct 09, 2011 12:07 pm**

bffulgham wrote: I proudly showed the set to the spouse, and she showed great admiration (she likes me, you see). I suggested that we give the kids, in-laws, out-laws, and co-workers pens for Christmas. She said, "Yes, I think that would be a good way to handle the gift-thing. But, can you etch or carve the recepient's name in the pen? Otherwise, it's just a pen".

Ooh, another reason to build a rotary on to my CNC router. Vcarve engrave pen and other turnings! (Yes, I could CNC pens, and might for mass-production, but where would be the fun in that.)

Roy

Posted: **Sun Oct 09, 2011 8:33 pm**

Could use the cnc to pocket the name into one side of the pen blank then either fill the pocket before turning or after.

Shopsmith Forums

A question for you pen turners