Me too!!:(bdegarmo53 wrote: I'm beginning to agree with 'reible' and think something has happened to the SI internally (defective).
Speed increaser comes loose
Moderator: admin
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
I have to insist that the SI is indeed moving on the way tubes. A 'still' look at 0:22 and another at 0:23 clearly shows the SI moved about an inch and a half(or more) and is evident both at the quill and the way tube clamps. The earlier wobbling of the cutter has me concerned. I am not familiar with the internals of the SI, but it appears to be a large bevel gear(or maybe rubber tired wheel) at the input shaft driving a smaller bevel gear(or driven wheel/plate) on the spindle shaft.
What could be causing a severe force against the quill shaft is a mystery. What does the coupling between the quill shaft and the SI look like. Could the coupling be causing this? Is a hub placed onto the quill shaft and an internal coupler fitting fixed to the SI input shaft?
I cannot envision anything external to the SI causing this.
What could be causing a severe force against the quill shaft is a mystery. What does the coupling between the quill shaft and the SI look like. Could the coupling be causing this? Is a hub placed onto the quill shaft and an internal coupler fitting fixed to the SI input shaft?
I cannot envision anything external to the SI causing this.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
My bad! For some reason, (Brain error), I thought you you had a PowerPro and were getting the harmonics from that.bdegarmo53 wrote: Jimthej, what do you mean by needing the parameters changed? If you're talking about the speed, the SS is set at U for routing/shaping.
Hmmm, 70,000 rpm shaper...
Can I say to myself... STOOOOPIIID!!!!
Jim in Bakersfield:D
-
joshh
- Platinum Member
- Posts: 723
- Joined: Tue Jan 08, 2013 8:53 pm
- Location: Dallas / Fort Worth, Texas
jimthej wrote:Hmmm, 70,000 rpm shaper...
Oh just you wait, someone will invent it
- 1986 Mark V 500 Mini
- 1985 Mark V 510 with reversible motor, bandsaw, jointer, and double-tilt.
I offer quality motor reversal, rebuilding, and rewiring. Contact me at HarbourTools@live.com
- 1985 Mark V 510 with reversible motor, bandsaw, jointer, and double-tilt.
I offer quality motor reversal, rebuilding, and rewiring. Contact me at HarbourTools@live.com
-
bdegarmo53
- Silver Member
- Posts: 9
- Joined: Thu Aug 01, 2013 4:18 pm
Not fixed after all ...
JPG40504, You're right. Not sure how I missed that in live action. Guess I was focused more on that spindle and the safety factor. I've got that way tube clamp on there as tightly as I can turn it by hand and after it moves I still can't budge it manually. Still, what kind of force could push this tightly clamped SI off the quill like that? Wow.
There's a five-groove hub tightened onto the shaft and the SI has a part inside to mate with it. The hub remains tight on the shaft when I take the SI off.
At a complete loss on explaining, much less fixing, this one.
There's a five-groove hub tightened onto the shaft and the SI has a part inside to mate with it. The hub remains tight on the shaft when I take the SI off.
At a complete loss on explaining, much less fixing, this one.
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Whatever is 'pushing', it has to be from the internal end of the input shaft. That implies the input shaft can move out towards the quill.
I do not think we will know what is causing this without a look inside.
I do not think we will know what is causing this without a look inside.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange