Fer a second I thought you had a racing stripe on the table!
Jigsaw
Moderator: admin
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Jigsaw
Not Boring!
Fer a second I thought you had a racing stripe on the table!
Fer a second I thought you had a racing stripe on the table!
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: Jigsaw
Looks good. How did you make it?
Mike
Mike
Re: Jigsaw
Marked it with a compass, cut it out on a scroll saw, drilled a 3/8" hole, using a brad point drill, run a 3/8" bolt through the hole, chucked it up in my Delta Mini lathe, worked it down to the correct size, using a body file, cut the slit with the scroll saw. It's really neat that you can look down and see what you are doing without looking under the table.
Don G
Don G
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Jigsaw
Even 'neater' with it removed!dgreen810 wrote:Marked it with a compass, cut it out on a scroll saw, drilled a 3/8" hole, using a brad point drill, run a 3/8" bolt through the hole, chucked it up in my Delta Mini lathe, worked it down to the correct size, using a body file, cut the slit with the scroll saw. It's really neat that you can look down and see what you are doing without looking under the table.
Don G
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: Jigsaw
Yep!!
Don G
Don G
Re: Jigsaw
dgreen810 wrote:Marked it with a compass, cut it out on a scroll saw, drilled a 3/8" hole, using a brad point drill, run a 3/8" bolt through the hole, chucked it up in my Delta Mini lathe, worked it down to the correct size, using a body file, cut the slit with the scroll saw. It's really neat that you can look down and see what you are doing without looking under the table.
Don G
I guess the reason it is removable is so you can remove it to change blades and not have to look under the table.John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
Re: Jigsaw
It's pretty obvious some of you guys haven't done much scroll sawing. Not that this jigsaw is a "Scroll Saw", but the principle is the same making piercing cuts.
Don G
Don G
- Attachments
-
- P1010005 (2015_11_11 18_39_05 UTC).JPG (115.28 KiB) Viewed 2704 times