Shopsmith Forums

For some reason the pictures aren't showing up in my browser--I'd like to see them. One day I'd like to devise a dust collection system myself.

chipmaster wrote:For some reason the pictures aren't showing up in my browser--I'd like to see them. One day I'd like to devise a dust collection system myself.

Here are links to click and view Chip. I hope this works for you...if not let me know and we'll try something else.

http://farm8.staticflickr.com/7027/6466 ... 00da_z.jpg
http://farm8.staticflickr.com/7018/6466 ... 7278_z.jpg
http://farm8.staticflickr.com/7022/6466 ... cd9a_z.jpg
http://farm8.staticflickr.com/7003/6466 ... 1db5_z.jpg

"Rubbermaid Brute tub on wheels"

Interesting, I once had a set up like that but if the inlet side of the hose got blocked off the sides of the Rubbermaid got sucked in until it lost its seal with a large woomth and scattered dust cloud as it attempted to expand back out.

I went to a galvanized metal garbage can that didn't have that problem.

Have you experienced that? Or maybe these tubs have gotten stronger/tougher. Anyway I'd like to here back from you on how that is all working out.

Ed

reible wrote:"Rubbermaid Brute tub on wheels"

Interesting, I once had a set up like that but if the inlet side of the hose got blocked off the sides of the Rubbermaid got sucked in until it lost its seal with a large woomth and scattered dust cloud as it attempted to expand back out. I went to a galvanized metal garbage can that didn't have that problem. Have you experienced that? Or maybe these tubs have gotten stronger/tougher. Anyway I'd like to here back from you on how that is all working out. Ed

Hey Ed, you are correct, that could be a problem. The guy at Rockler warned me that a plastic tub would not be strong enough. Rockler does not sell anything that would work (not too smart) but he did point me to http://www.uline.com to buy a fiber drum like the one on display in the store. Uline only sells them in pairs for $80 so I decided to just give old brute a try. I bought it 20 years ago from an industrial supply outfit and it's heavy duty. I suppose new models are not so stout. It works very well and I'm pleased with the setup. Except for the static...I need to get it grounded.

[ATTACH]15328[/ATTACH]


Some of you may remember that I had an Excalibur sliding table on this end of the Unisaw before I purchased the Mini Max. I decided it would be good to add another router table and lift to the shop by replacing the slider with this Bench dog cast iron router table with a Woodpecker lift and Porter Cable 3 1/4 hp router. It is an excellent set up but for some things I need a larger table.



Anyone recognize the support legs?



[ATTACH]15331[/ATTACH]

This should be big enough. 32" x 49"





[ATTACH]15329[/ATTACH]

Now I have to have access to the lift mechanism so I will have to provide a hole in the appropriate location.






[ATTACH]15330[/ATTACH]







[ATTACH]15332[/ATTACH]

Guess I had better head in for the evening before my Wife throws my dinner out!

[attach]15346[/attach]





[attach]15349[/attach]

I want to be able to use the fence so I needed to route 2 slots.





[attach]15347[/attach]





[attach]15348[/attach]

Also decided to radius the corners. I'm sure my middle body parts will thank me later.






[attach]15350[/attach]

The really nice thing about a Shopsmith.

[attach]15351[/attach]

Decided to drill some shallow holes in the bottom side to hold the legs in place. I had to drill the hole for the lifting rod by hand as it was just out of reach on the 520.







[attach]15352[/attach]

I installed a 1/4 inch bit and lowered the router bolted the top in place and used the lifting rod to pull the bit through the top. I then had a starter hole for the hole saw.




[attach]15353[/attach]

A 4 inch hole saw is hard on batteries!






[attach]15354[/attach]

I cleaned up all the edges with either a 1/4" roundover or a small chamfer.






[attach]15355[/attach]

I think this will handle a pretty large panel. Next I located and drilled two 1/2" holes for the starting pins but the picture did not come out well.

[ATTACH]15356[/ATTACH]

Here is a nice little trick. When drilling holes in a wall use a little painters tape to catch the crumbs.







[ATTACH]15357[/ATTACH]

Just hanging out until needed.

Guards we don't need no Stinking Guards!!!:eek:


At least that is what I told the wife when she reminded me that I had not installed the guard on the Mini Max today. Actually I have been planning to purchase the needed items to hook it up to the dust collector so while I was out shopping today I picked those up.



[ATTACH]15361[/ATTACH]







[ATTACH]15362[/ATTACH]







[ATTACH]15363[/ATTACH]

I am going to rig up something to hang this from the ceiling.







[ATTACH]15364[/ATTACH]

These quick connect clamps from Woodcraft work great if you need the ability to move your vac hoses around. They have them in 4" and 2 1/2" sizes.

This is another shop improvement project brought on by necessity.




[attach]15483[/attach]







[attach]15484[/attach]