Shopsmith Forums

Thanks but I'll have to pass. This project had to be put on the back burner for a bit.

hello,

was wondering if someone could help me out and understand what I need to purchase and where I could purchase a molder and router attachments? and also the tools for them(the knives or bits). I am a new owner of this wonderful machine and wanted to get a few of the attachments.

I read I can get craftsman products but was hoping for help on what i should be looking for when I get them. I want to also get dado blades.

THanks for any help.

For a SAWsmith?

Jhcess19 wrote:hello,

was wondering if someone could help me out and understand what I need to purchase and where I could purchase a molder and router attachments? and also the tools for them(the knives or bits). I am a new owner of this wonderful machine and wanted to get a few of the attachments.

I read I can get craftsman products but was hoping for help on what i should be looking for when I get them. I want to also get dado blades.

THanks for any help.

1. The molder and router attachments made by Shopsmith were designed for use on all the Shopsmith machines as well as the Sawsmith. The molder will mount directly on the shaft without any arbor. It is 556213 Shopsmith Molder Head ...    $98.70. Shopsmith has a complete selection of knives to use with it.

2. For routing you need to buy 514631 Router Chuck - 1/2" ...   $22.21 or 514632 Router Chuck - 1/4" ...   $22.21. Shopsmith also sells router bits for both 1/2" or 1/4" shank. I particularly like the router bits made by Bosch as well as Wisconsin Knife Works. I do not recommend buying Craftsman.

None of the other molder or router items from Shopsmith can be used on the Sawsmith such as the Safety Shield so don't buy any of their kits that include such items.

3. The CMT 6" carbide dado sold by Shopsmith is excellent and will work fine but any 5/8" arbor dado will work fine as long as your Sawsmith arbor nut is not missing. If it is then you will need to purchase a 5/8" arbor from Shopsmith.

Yes for a sawsmith

stephen_a._draper wrote:

Jhcess19 wrote:hello,

was wondering if someone could help me out and understand what I need to purchase and where I could purchase a molder and router attachments? and also the tools for them(the knives or bits). I am a new owner of this wonderful machine and wanted to get a few of the attachments.

I read I can get craftsman products but was hoping for help on what i should be looking for when I get them. I want to also get dado blades.

THanks for any help.

1. The molder and router attachments made by Shopsmith were designed for use on all the Shopsmith machines as well as the Sawsmith. The molder will mount directly on the shaft without any arbor. It is 556213 Shopsmith Molder Head ...    $98.70. Shopsmith has a complete selection of knives to use with it.

2. For routing you need to buy 514631 Router Chuck - 1/2" ...   $22.21 or 514632 Router Chuck - 1/4" ...   $22.21. Shopsmith also sells router bits for both 1/2" or 1/4" shank. I particularly like the router bits made by Bosch as well as Wisconsin Knife Works. I do not recommend buying Craftsman.

None of the other molder or router items from Shopsmith can be used on the Sawsmith such as the Safety Shield so don't buy any of their kits that include such items.

3. The CMT 6" carbide dado sold by Shopsmith is excellent and will work fine but any 5/8" arbor dado will work fine as long as your Sawsmith arbor nut is not missing. If it is then you will need to purchase a 5/8" arbor from Shopsmith.

Thanks so much. I am pretty excited to get to work. For shaping, if I buy a bunch of bits will they work with this sawsmith? Or do I need to make sure of size of blades?

For Shaping on the Sawsmith you will need to purchase a Shopsmith 1/2" arbor and then you can use any 1/2" shaper cutter. For shaping and routing you will run the Sawsmith at 6400 rpm. For sawing, dado, and molding you will run it at about 3400 rpm. The numbers on the dial tell you how many hundred rpm. Just make sure the motor is turned on when changing speeds. Do not turn the speed dial with the motor turned off.

How do I oil the sheaves? I am unable to remove the belt assembly cover. It seems a ring with a hex key set screw is over the right output arbor shaft. Thanks

bob84 wrote:How do I oil the sheaves? I am unable to remove the belt assembly cover. It seems a ring with a hex key set screw is over the right output arbor shaft. Thanks

It sounds like there and arbor or some other accessory on the right shaft, loosen the set screw and remove that arbor/accessory. then remove the cover.
See the manual page 12. http://vintagemachinery.org/pubs/791/3287.pdf

I am trying to oil the sheaves and thus need to remove the belt guard cover.
I can remove the four screws that hold the belt guard in place. However, a collar ring is held on by this hex set screw and not being able to get the hex set screw off the arbor prevents me from getting the belt guard cover off.
There is not enough clearance to get a hex key wrench into unscrew the hex set screw (see red arrow in the picture).
Anyone know what is the size of the hex set screw? Or what is the procedure to remove the hex set screw and belt guard cover. If I knew the size of the hex set screw I thought I would grind off an hex key wrench to the correct length to fit between the belt guard and into the collar.