Can't figure out how to make this cut
Moderators: HopefulSSer, admin
Can't figure out how to make this cut
I am making a coffee table and the legs have beveled feet.
The wood is 3 1/2 inches wide and the cut is 1 5/8 of the bottom and 4 1/4 on the side. (I hope this makes sense...if not, I can post a picture)
My miter gauge only goes to 30 degrees so I can't make the cut with just that on my SS table saw.
Any suggestions? I don't have (or have access to) a power miter saw.
Thanks!
The wood is 3 1/2 inches wide and the cut is 1 5/8 of the bottom and 4 1/4 on the side. (I hope this makes sense...if not, I can post a picture)
My miter gauge only goes to 30 degrees so I can't make the cut with just that on my SS table saw.
Any suggestions? I don't have (or have access to) a power miter saw.
Thanks!
Morgan
Blue Springs, MO
SS Mark 7 PP
Blue Springs, MO
SS Mark 7 PP
Most folks make this cut using a rip fence with a jig to set the wood at the proper angle.
http://www.newwoodworker.com/usetaperjig.html
Just google "ripping tapers on a table saw" and you'll get lots of ideas.
http://www.newwoodworker.com/usetaperjig.html
Just google "ripping tapers on a table saw" and you'll get lots of ideas.
Octogenarian's have an earned right to be a curmudgeon.
Chuck in Lancaster, CA
Chuck in Lancaster, CA
mikhelee wrote:I was setting up to cut up an 8 foot long by about a foot wide piece of plywood. The plan was to use a sled and then add the extension tables as support.
Hi Jim! Welcome to the Forum! You must be cross cutting that foot wide piece of plywood - right? If that is so - you are on the right track.
Or if you are planning on ripping one foot off of the side of an 8 ft. by 4ft. plywood sheet - it would be easier to use a hand held saw to rip off a foot. You'll need a guide to rip this exactly but another option would be to use a hand held saw (skill saw type) to rip off about a foot plus an inch or so. Then with the aid of onfeed and off-feed support you can use your Shopsmith and rip fence to rip that piece to 1 ft. exactly.
Octogenarian's have an earned right to be a curmudgeon.
Chuck in Lancaster, CA
Chuck in Lancaster, CA
Well, she's not the prettiest gal at the ball, but I think she'll do the trick!charlese wrote:Most folks make this cut using a rip fence with a jig to set the wood at the proper angle.
http://www.newwoodworker.com/usetaperjig.html
Just google "ripping tapers on a table saw" and you'll get lots of ideas.
Thanks for pointing me in the right direction.
- Attachments
-
- IMG_20120918_222448.jpg (38.83 KiB) Viewed 2487 times
Morgan
Blue Springs, MO
SS Mark 7 PP
Blue Springs, MO
SS Mark 7 PP
That looks right to me. It's a jig not a piece of furniture.
Mike......... Rowlett, Texas, near Dallas
86 MK V 500/520. 59 MK 5 Greenie Shorty. SS Jointer, SS Planer,
SS Bandsaw, SS Lathe duplicator, SS Belt Sander,SS Molder & Shaper,
SS Tenon master jig, SS Mortising kit, SS 2 1/4' Drum Sanders, Ringmaster, DC3300....
86 MK V 500/520. 59 MK 5 Greenie Shorty. SS Jointer, SS Planer,
SS Bandsaw, SS Lathe duplicator, SS Belt Sander,SS Molder & Shaper,
SS Tenon master jig, SS Mortising kit, SS 2 1/4' Drum Sanders, Ringmaster, DC3300....
- JPG
- Platinum Member
- Posts: 34693
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
You learn quick and quite well!
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
wrmnfzy wrote:WOOD there be any advantage to making it so it saddled over the fence?
Depends on the operator's preferences. Also the builder's desires. This jig is only going to be used occasionally. There would be no advantage for me to have it saddle the fence.
Octogenarian's have an earned right to be a curmudgeon.
Chuck in Lancaster, CA
Chuck in Lancaster, CA