Shop Made Accessory Shelf
Moderators: HopefulSSer, admin
Shop Made Accessory Shelf
I have gone the Under Shopsmith cabinet route a couple times. The first one (plywood) came with a Shopsmith and I used it for several years but had to go to another Shopsmith to do horizontal boring. The second one was oak and I just used the cabinet case and cut it down to just fit between the table posts and put all new drawers in it. Only problem was the drawers were not deep enough for the 12 inch sanding disk.
I decided to go back to a shop made accessory shelf.
While I was making changes I added threaded rod and knobs to the bandsaws.
Merry Xmas to y'all.
I decided to go back to a shop made accessory shelf.
While I was making changes I added threaded rod and knobs to the bandsaws.
Merry Xmas to y'all.
Mark 7 Power Pro, Mark V 510, Mark VII (early 1960s) Headstock wall mount drill press on Mark 5 way tubes, Mark 5 Shorty with reversible motor, Overhead Pin Router, Power station with band saw, Jointers, Belt Sanders, Strip Sander, Scroll saw, Jigsaw, Shopsmith Lathe Duplicator, Craftsman 2.5 hp 13" Planer/molder, Craftsman 5 hp 12-inch planer molder, myriad Shopsmith accessories, Harbor Freight sawmill with extensions to cut 22' logs.
Re: Shop Made Accessory Shelf
NICE !!! beautiful lumber and workmanship
- rjent
- Platinum Member
- Posts: 2121
- Joined: Fri Mar 14, 2014 3:00 pm
- Location: Hot Springs, New Mexico
Re: Shop Made Accessory Shelf
Good job! Looks functional ...
Is that curly Maple???????
Is that curly Maple???????
Dick
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....
"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....
"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
Re: Shop Made Accessory Shelf
Thanks for the positive comments. I believe it is curly maple sometimes called tiger maple. It happened to be one of the first trees I cut on this property because I needed fire wood. Much of the tree top was dead. When I found out what it was I saved most of trunk.
11/1/2020 Edit: Removed 3D Warehouse url
11/1/2020 Edit: Removed 3D Warehouse url
Mark 7 Power Pro, Mark V 510, Mark VII (early 1960s) Headstock wall mount drill press on Mark 5 way tubes, Mark 5 Shorty with reversible motor, Overhead Pin Router, Power station with band saw, Jointers, Belt Sanders, Strip Sander, Scroll saw, Jigsaw, Shopsmith Lathe Duplicator, Craftsman 2.5 hp 13" Planer/molder, Craftsman 5 hp 12-inch planer molder, myriad Shopsmith accessories, Harbor Freight sawmill with extensions to cut 22' logs.
Re: Shop Made Accessory Shelf
Edit: 11/01/2020 Changed 3d warehouse url
https://3dwarehouse.sketchup.com/model/ ... f-10282020
Moved the miter gauge further to the left. Added distances for starting points for hole locations and centers of circular holes. Moved live center, drive spur and removed small lathe tool support from the drawing. Also added a 1x4 to the bottom of the shelf to prevent sag.
https://3dwarehouse.sketchup.com/model/ ... f-10282020
Moved the miter gauge further to the left. Added distances for starting points for hole locations and centers of circular holes. Moved live center, drive spur and removed small lathe tool support from the drawing. Also added a 1x4 to the bottom of the shelf to prevent sag.
Mark 7 Power Pro, Mark V 510, Mark VII (early 1960s) Headstock wall mount drill press on Mark 5 way tubes, Mark 5 Shorty with reversible motor, Overhead Pin Router, Power station with band saw, Jointers, Belt Sanders, Strip Sander, Scroll saw, Jigsaw, Shopsmith Lathe Duplicator, Craftsman 2.5 hp 13" Planer/molder, Craftsman 5 hp 12-inch planer molder, myriad Shopsmith accessories, Harbor Freight sawmill with extensions to cut 22' logs.
Re: Shop Made Accessory Shelf
I cut out the saw guard hole on a new shelf today and found the guard was a little tight in the hole. I adjusted the dimensions in the file by 1/16" on both sides at the top in the Sketchup drawing.
Mark 7 Power Pro, Mark V 510, Mark VII (early 1960s) Headstock wall mount drill press on Mark 5 way tubes, Mark 5 Shorty with reversible motor, Overhead Pin Router, Power station with band saw, Jointers, Belt Sanders, Strip Sander, Scroll saw, Jigsaw, Shopsmith Lathe Duplicator, Craftsman 2.5 hp 13" Planer/molder, Craftsman 5 hp 12-inch planer molder, myriad Shopsmith accessories, Harbor Freight sawmill with extensions to cut 22' logs.
Re: Shop Made Accessory Shelf
I have been searching for a plan for the accessory shelf and it looks like you have one. Problem is I can't seem to be able to access it. What app do I need to open the drawing and see all of the deminsions. Thanks in advance for your help.
Re: Shop Made Accessory Shelf
Here's one, but it might be more than you want. In PDF form.
- Attachments
-
- Under SS storage.pdf
- (635.03 KiB) Downloaded 198 times
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
.
.
Bob
Re: Shop Made Accessory Shelf
The accessory shelf above was drawn with Sketchup 2017 I believe. It has expired on my computer. I opened it with Sketchup viewer from the file I stored but I cannot get a clear print. The current Sketchup free online is useless, JMHO. I will attempt to put dimensions in a pdf format later this week and attach. The file is on 3D Warehouse if anyone has A working version of Sketchup (Shopsmith Accessory Shelf 10282020) https://3dwarehouse.sketchup.com/model/ ... f-10282020
Mark 7 Power Pro, Mark V 510, Mark VII (early 1960s) Headstock wall mount drill press on Mark 5 way tubes, Mark 5 Shorty with reversible motor, Overhead Pin Router, Power station with band saw, Jointers, Belt Sanders, Strip Sander, Scroll saw, Jigsaw, Shopsmith Lathe Duplicator, Craftsman 2.5 hp 13" Planer/molder, Craftsman 5 hp 12-inch planer molder, myriad Shopsmith accessories, Harbor Freight sawmill with extensions to cut 22' logs.
Re: Shop Made Accessory Shelf
FYI the last free version of 2017 is still available here:
https://help.sketchup.com/en/downloading-older-versions
It still works but getting dated. That is what I have and use.
Ed
https://help.sketchup.com/en/downloading-older-versions
It still works but getting dated. That is what I have and use.
Ed
{Knight of the Shopsmith} [Hero's don't wear capes, they wear dog tags]